Printer Friendly

Submetering Best Practices for Multi-Tenant Buildings: HOW TO GET MORE ACCURATE RESULTS WITH FEWER HEADACHES.

Is your team still using clipboards to record submetering data? Many buildings with submetering systems still rely on manual input for at least part of the process, which creates plenty of opportunities for mistakes. Find waste, eliminate bad data and make the whole process easier and more efficient by automating as much of your submetering as possible.

Common Submetering Problems

Buildings with outdated submetering systems and old infrastructure tend to bill tenants by assigning proportionate shares that correlate with the physical spaces tenants occupy, says Anna Buglaeva, vice president of growth for Aquicore, an IoT-driven asset management provider.

The obvious problem with this strategy is that not all organizations use the same amount of electricity. An office may only need a few watts per square foot, while an energy-intensive data center would use much more. A submetering system that can support tenant billback solves this problem.

"Sometimes building owners choose to purchase cheaper equipment that doesn't have industry standard language protocols other data loggers can plug into and send data," Buglaeva says. "Some owners opt to purchase ones that can only be manually read. That presents a problem because you're investing in a tool that will forever have to have a human walk around and read it. People are best used to make decisions, not write down numbers day in and day out."

Spending time recording numbers and putting them into an Excel spreadsheet is error-prone and tedious. The time spent manually entering measurements could be better used looking for trends and anomalies, such as pinpointing and addressing areas that are using a disproportionate amount of energy, explains Bala Marimuthu, product manager for digital products and solutions for Siemens.

Get Smarter about Submetering

Before you upgrade your submetering system, Buglaeva recommends hiring a mechanical engineer to update your building's electrical documentation, especially if you're not the original owner of your building.

"Things get complicated and challenging [with] outdated and old building systems that have been renovated time and time again but not documented, because owners choose not to pay for updated drawings," she says. "You end up with a hodgepodge of comingled panels that don't feed multiple floors, and you don't know what you're picking up when you implement a tenant billback solution with submeters."

Next, decide which building systems you'll monitor, Buglaeva advises. Central plants and air handling units are a good place to start. For a deeper dive, you can monitor BTU consumption and see how much energy it takes you to supply air at a given temperature. However, some building types don't need information at the BTU level.

With office buildings where you have a regular schedule, you can make many decisions without going too granular. "You can pick up two or three major systems and set the load curve," Buglaeva says. "You have an input of the building running from 8 a.m. to 6 p.m., so you know that something is not working properly when your base load is high between the hours of 8 p.m. to 4 a.m."

Buildings with nonstandard operating hours, like hotels or convention centers, need more information. That means submetering additional systems or even separating individual floors, Buglaeva adds. You should also periodically tune up any other automation infrastructure that's installed in your building and make sure your automation software and submetering solution can speak to each other, Marimuthu recommends.

How to Shop for Submeters

Marimuthu recommends investing in a submetering solution with remote data logging (thus ending the physical journey to read each meter in person once and for all), as well as automatic notifications whenever the system detects a significant issue.

All submeters should be web-enabled and capable of being manually read for accountability purposes. They should also use one of the most common communication protocols so they can alert you when they need to be replaced, Buglaeva says. They should also be paired with current transformers that are appropriately sized for the load going through the panel they're on.

"If your current transformer is oversized for the load, you're not collecting enough money as an owner," Buglaeva explains. "You're basically giving your tenants free electricity."

Overwhelmed? Don't be. Find a solutions provider who can implement both the software and hardware elements of your tenant billback solution thoughtfully. Insist on a contract that includes quality control and verification that all the systems are functioning properly. And make sure you're working with an MEP engineer and an electrical contractor on the installation.

"If you don't have a team, don't do it," Buglaeva adds. "I don't think anybody can do it alone."

Janelle Penny (janelle.penny@buildings.com) is the editor-in-chief of BUILDINGS.
COPYRIGHT 2019 Stamats Communications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2019 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:THE ENERGY MANAGER
Comment:Submetering Best Practices for Multi-Tenant Buildings: HOW TO GET MORE ACCURATE RESULTS WITH FEWER HEADACHES.(THE ENERGY MANAGER)
Author:Penny, Janelle
Publication:Buildings
Date:Jul 1, 2019
Words:776
Previous Article:Tips for Purchasing New Technology: SURVEY FINDS FIVE FACTORS FOR A SUCCESSFUL TRANSACTION.
Next Article:What is the Urban Heat Island Effect? THE FACTORS BEHIND THIS PHENOMENON AND WHAT YOU CAN DO ABOUT IT.
Topics:

Terms of use | Privacy policy | Copyright © 2019 Farlex, Inc. | Feedback | For webmasters