Printer Friendly

Safe and sound; A discreet safe to keep valuables protected isn't just something for the rich and famous to consider. Here's how to fit one at your home.

Byline: YOUR HOME With Bake Off finalist and builder Richard Burr

o you own things? Valuable things? DMaybe a passport or two? A bit of cash? Some jewellery? Want to keep hold of them when you're not home? Then this is the job for you.

Wall safes are easy to install and with a picture over the front of them, they are nearly impossible to spot, too. This guide shows how to install a safe in a brick wall, though stud wall mounted safes are also available.

DO YOU HAVE A SUITABLE WALL? If you have a house with a disused fireplace, that's the perfect place for a wall safe, as there will be a hollow void behind the chimney breast.

If you don't have a chimney breast to use, there are all sorts of other safes - under-floorboard safes, ones to bolt to the wall, fitted into stud walls - but this guide is for your classic, 'picture on a hinge to reveal the safe underneath' safe (even if the USB stick inside just has back-ups of family photos, rather than the nuclear codes that James Bond is looking for).

WHICH SAFE SHOULD YOU CHOOSE? There are so many different safes to choose from, including ones that are fire and water-resistant, though these are considerably more expensive.

Many safes are guaranteed up to a particular value of cash or goods too, which will be indicated when you buy it. Safes will also indicate how many bricks need to be removed.

You can decide for yourself whether you want a key or a combination safe too. I prefer a key safe, as they're often used so rarely you (well, I) can forget the combination code.

I opted for the Burg Wachter Point Wall Safe (pictured right) from, which is just over PS100.

MAKING THE HOLE Mark roughly where the safe is going and chip off some plaster until you reach the brick surface behind it. Most wall safes are designed to fit standard brick sizes, so once you've found the dimensions of one brick, you can work out where your safe outline will be.

You then need to do a technique called 'stitch drilling'. Bricks are always laid in a formation known as a bond. Exactly how you build a Lego structure, this is where you lay a row (course) of bricks and then the course on top overlaps the joints. This is called 'half bond' and it's the type of bricklaying you're most likely to come across.

To fit a three-brick safe, you'll need to remove a whole brick and the whole brick two courses below, but in between, you need to remove two half bricks. To do this you need an electric drill and a masonry bit for the 'stitch drilling.'.

Set your drill to hammer setting and drill four vertical holes through the centres of the middle two bricks, along the line of the bricks above and below. Work hard to make sure you're drilling into these straight and level.

When you've drilled into both middle bricks, use a heavy hammer and a bolster to break the bricks in half along the line where you've drilled the holes.

Use your drill bit to buzz through the mortar joints on the top and bottom bricks, and you should be able to pull each of the bricks out.

FITTING THE SAFE Place the safe in the hole and check it's level using a spirit level - you may have to wedge a corner up with a some folded up card.

When you're fitting a safe into a wall, rather than drilling and screwing it into place, you can set it with readymixed concrete available cheaply from stores like B&Q, but avoid the quick-setting stuff.

Wedge your safe into the hole and sit it on two small wooden blocks or pieces of cardboard. Wedge the sides too, so there are small gaps all around the safe. Mix your concrete in the tub, but you'll need two things to apply it - a plastering hawk (or a square of wood if you don't want to get one of these) and a pointing trowel.

Dollop your concrete onto your hawk and chop it with your trowel. Gradually poke small amounts of the concrete into the cavity around your safe, using your trowel to smooth it down. Check with your spirit level that the safe and the cement are flush with the wall and leave it to set overnight.

FINISHING THE JOB The main thing to remember when it comes to finishing off the job, is that you're probably going to cover the safe with a picture, so it doesn't need to be perfect underneath.

But where your plaster has been chipped away, fill this in with multipurpose Polyfilla and when dry, paint this the same colour as your wall.

You can then hang a picture over the safe or even attach the picture to the wall with a hinge and a magnetic catch for extra drama. Now, forget I said any of this and don't go looking behind any of the pictures in my house, capeesh?


There are many different safes to choose from says Richard
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2017 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Features
Publication:The Journal (Newcastle, England)
Date:Dec 2, 2017
Previous Article:CHECK MATE... Bring a warm country feel to your home with classic check pieces, write amber graafland and didi danso.
Next Article:be safe this festive season; A few simple steps to stop your home becoming a Christmas casualty.

Terms of use | Privacy policy | Copyright © 2020 Farlex, Inc. | Feedback | For webmasters