Printer Friendly

Articles from Mechanika (January 1, 2017)

1-21 out of 21 article(s)
Title Author Type Words
Analysis of effect of impeller geometry including blade outlet angle on the performance of multi-pressure pumps: Simulation and experiment. Mohammadi, N.; Fakharzadeh, M. Report 4957
Analysis of wheel-rail contact under partial slip and low speed conditions. Ozdemir, Y.; Voltr, P. Report 3463
Determination of the most appropriate surgical treatment in syndesmotic injury of ankle joint: Application of Taguchi method. Gocer, H.; Cirakli, A.; Ugur, L.; Yildiz, A.; Karadeniz, S. Report 6328
Effects of arrangement and phase difference of oscillation of synthetic jets on heat transfer in micro-channels. Khaleghinia, J.; Kowsary, F.; Aghanajafi, C. Report 3743
Enhancements of thermal performances of an active magnetic refrigeration device based on nanofluids. Chiba, Y.; Smaili, A.; Sari, O. Report 2976
Exergy efficiency of a ventilation heat recovery exchanger at a variable reference temperature. Martinaitis, Vytautas; Bielskus, Juozas; Janusevicius, Karolis; Bareika, Paulius Report 4427
Experimental research on eutectic refrigerating system with economizer. Vaitkus, L.; Dagilis, V. Report 5664
Extended isogeometric analysis using analysis-suitable T-splines for plane crack problems. Habib, S.H.; Belaidi, I. Report 3792
Finite element and isogeometric correlation analysis using modal assurance criterion. Asma, F.; Kacel, S. Report 2701
Investigation of the ESP cleaning efficiency of the flue gases in the wide range of Re numbers. Poskas, R.; Sirvydas, A.; Poskas, P.; Simonis, V.; Jankauskas, J. Report 4801
Mechanical model for fracture toughness assessment. Baron, A.A. Report 2848
Modelling of heat and mass transfer processes in phase transformation cycle of sprayed water into gas: 5. Numerical modelling optimization of phase transformation cycle for droplets slipping in gas flow. Miliauskas, G.; Maziukiene, M.; Puida, E. Report 5739
Numerical analysis of compound heat transfer enhancement by single and two-phase models in parabolic through solar receiver. Benabderrahmane, Amina; Benazza, Abdelylah; Laouedj, Samir; Solano, J.P. Report 3819
Numerical analysis of the counterintuitive dynamic behavior of the elastic-plastic fully-clamped beams under impulsive loading. Alizadeh, Mehdi Shams; Shirazi, Kourosh Heidari; Moradi, Shapour; Sedighi, Hamid Mohammad Report 5300
Numerical study of lateral wind effect on parachute dropping based on finite element method. Cheng, H.; Wei, L.; Zhou, B.; He, Q.; Xiao, P. Report 2825
Prediction of and experimental study on cutting force of austempered vermicular graphite cast iron using artificial neural network. Mavi, Ahmet; Ozden, Semih; Korkut, Ihsan Report 3577
Research of factors influencing the burnout quality inside a biomass combustion chamber. Vonzodas, T.; Pedisius, N.; Dziugys, A. Report 6806
Research on design of the smart factory for forging enterprise in the industry 4.0 environment. Pei, Fengque; Tong, Yifei; He, Fei; Li, Dongbo Report 4224
Rope-free elevator system based on planar positioners for vertical and horizontal transport. Trochimczuk, R.; Huscio, T. Report 3934
Study on the interaction of electric vehicle roll and battery pack stability. Fan, Yuezhen; Sun, Jie Report 2930
Theoretical and experimental investigation of backlash effects on a 2-DOF robotic balancing table. Bayar, G. Report 4542

Terms of use | Privacy policy | Copyright © 2020 Farlex, Inc. | Feedback | For webmasters