Printer Friendly

Learn to set and retrieve an anchor: it's an important safe-boating skill.

Knowing how to anchor safely is an important seamanship skill that every boat operator should master. There will certainly be times you'll want to stop in a sheltered spot for swimming, fishing, lunch or an overnight stay. But in bad weather, or if you experience engine failure, the only alternative to setting the anchor may be washing ashore or drifting out to sea. Anchoring is an easy task if you follow these guidelines.

(1) Approach

Choose an area clear of boats and underwater obstacles. Check your chart to make sure there are no cables, wrecks or obstructions on the bottom to foul your line. Determine the water depth and type of bottom (preferably sand or mud). Calculate the amount of anchor line you need to let out. The general rule is five to seven times as much line as the depth of the water plus the distance from the surface of the water to where the anchor will attach to the bow. Secure your anchor to the bow cleat at the point on the line where you want it to stop. Then, with your boat heading into the wind (or current, if that is stronger) move into the area, put your engine in idle and bring your boat to a stop with the bow just forward of where you intend to drop anchor.

(2) Lower the Anchor Slowly

With the vessel stopped and your life jacket on, lower the anchor slowly into the water from the bow. Do not throw it over the side, as this tends to foul the line. As you lower the anchor, your boat should begin to drift backward with the wind or current, allowing the anchor to move down and away as it enters the water. If your boat is stationary when the anchor reaches bottom, the chain may pile on top of it and prevent it from digging in. If your boat is not drifting backward on its own, put the engine in reverse and move slowly back as you pay out the anchor rode.

(3) Keep Tension in the Anchor Rode

This keeps the bow of the boat pointed toward the anchor, which ensures that your anchor, chain and rope stay straight and don't tangle. If you're anchoring in strong winds, you may actually have to put the engine in forward gear to control the speed and direction of backward drift.

Know Which Anchor You'll Need

There are anchors for every type of bottom and purpose. When deciding which is right for your boat, consider the type and weight of your vessel, the average depth of the water, the strength of the wind and/or current, the diameter of the anchor line and, most important, the bottom characteristics in the area you boat.


The most common types of anchors are the following.

The Danforth anchor (A) is lightweight and holds well in mud and sand, as well as rocky bottoms, if set carefully.

Many recreational boaters prefer the Plow anchor (B), because it demonstrates superior holding on most bottoms, including grass and weeds, but not on rocky bottoms.

The Mushroom anchor (C) buries well and holds best in sand or mud but may be difficult to retrieve. It is often used for anchoring mooring buoys.

The Bruce or Claw anchor (D) was developed originally for offshore oil and gas drilling rigs. It's a good burying type and holds well in sandy bottoms and mud.

The Navy or Admiralty type is an old reliable and familiar to most people, but it can be awkward to stow on board. The Grapnel (E) is small and easy to stow, which makes it a frequent choice for small vessels and open boats. The flukes are not particularly strong, however.


(4) Set the Anchor

With the anchor rode out and the boat in the intended swing zone, secure the rode and let the anchor dig in and stop the boat. Exercise caution as you do this. Wrap the rode once or twice around a cleat and keep your hands clear. Once you feel the anchor begin to dig in and set, put the engine in idle reverse and back down on the anchor to secure it to the bottom. This is especially important in areas where the bottom has a layer of sand and grass. Once the anchor is set, take note of any reference points (landmarks) in relation to the boat. Check these points frequently to make sure you're not drifting.

(5) Weigh Anchor

Once you've set the anchor, pulling it up or "weighing anchor" should be easy. Still, proceed with care and wear your life jacket during any anchoring evolution. The combination of anchor pull, current and weight can sometimes swamp a small boat. Lift the anchor as vertically as possible, and be careful it doesn't hit the side of the boat. Wash the anchor of mud and debris as you lift it.


TIP Calculate the amount of anchor line you will need to let out. The general rule is five to seven times as much line as the depth of water plus the distance from the surface of the water to where the anchor will attach to the bow.


I'm the guy who didn't heed the warning to never anchor by the stern. Sure, I'd heard the warning plenty of times, but nobody ever told me why. After all, it seemed so convenient, and that cleat on the port quarter was in the perfect spot. Oh yeah, this'll be fine. Or so I thought. Fortunately, I was one of the lucky ones and didn't lose the boat.

I've since learned that anchoring by the stern has caused many boats--small boats especially--to capsize and sink. The reason is that the transom is usually squared off and has less freeboard than the bow. Plus, the stern may be carrying the added weight of a motor, fuel tank, passengers and gear brought on board. In a strong current, that added weight and the force of the water could pull the stern under. Anchoring at the stern also makes the boat vulnerable to swamping from wave action.

Boaters make a lot of anchoring mistakes, and it's a matter of debate as to which ones occur most often. Just ask the guy who threw his anchor over the side without first attaching it to the line. Or the guy who fumbled the anchor and punched a hole in the bottom of his boat. Or the one who simply dropped it on his foot. Operators should be very careful when anchoring their boat.

I will argue that the most important thing to remember is to never anchor from the stern--although I must admit that tossing your anchor in the drink without first attaching it to the boat will make you feel pretty foolish. That reminds me: Keeping a spare anchor on board is not a bad idea.

COPYRIGHT 2011 Duncan McIntosh Company, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2011 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:coast guard: anchoring
Author:Jensen, Gary
Publication:Boating World
Geographic Code:1USA
Date:Feb 1, 2011
Previous Article:Request granted.
Next Article:Stay in control: maintenance of your boat's engine control system is vital.

Terms of use | Privacy policy | Copyright © 2021 Farlex, Inc. | Feedback | For webmasters |