Printer Friendly

Large two-platen presses gain speed & flexibility.

* An improved line of large two-platen injection presses offers new sizes plus greater speed, reduced maintenance, more operator-friendly design, and added flexibility for a range of molding requirements. The upgraded Maxima line from Cincinnati Milacron ranges from 1125 to 6600 tons. They are designed to accommodate the growing popularity of multi-component injection, stack molds, extra-large mold carriers, and ability to handle everything from flat to deep-draw parts. They also provide easier access for maintenance. The new presses are also "global" machines in that they will be built identically in the U.S., Germany, and China, except for electrical standards, safety provisions, and other local preferences.

Low-deflection clamp

The newest Maxima line replaces the MM and ML series and adds four new sizes--1460, 2025, 2990, and 4385 tons. Previously available sizes have been adjusted for today's global markets: 1125, 1300, 1820, 2330, 2585, 3315, and 6600 U.S. tons.

These presses retain design elements of the Maxima line. One of the most important features is the short-stroke central clamping cylinder on the moving platen. This produces 50% less platen deflection than most other two-platen presses, which clamp at the ends of the four tiebars and tend to "wrap" the platen around the mold, according to chief engineer Ron Hertzer. The result, he says, is less mold wear and improved part quality. Another key feature that differs from most other two-platen presses is full support of the tiebars from end to end. In particular, a rigid frame supports the ends near the moving platen.

Support for the platens carrying larger molds has been increased on the new models. Large "skates" under the moving platen and attached clamp-cylinder not only provide longer guided length but are also adjustable--a reportedly unique feature that ensures parallelism for heavy molds.

Here's what else is new on the updated Maxima models:

* Increased stroke and daylight--This has become important to molders of large parts such as "wraparound" auto fascias, says director of marketing Robert Strickley. He notes that to produce a 90-gal trash bin on an older Maxima 3500-ton machine, the molder had to pay extra for optional extended daylight. Now that part can be molded with the standard daylight specs. On the smallest model in the series, an 1125-tonner, the stroke is now 1900 mm and daylight is 2400 mm.

* Removable ejector box--On models of 1820 tons and up, this further increases the daylight capability for molds that don't require machine ejection. This feature allows one machine to mold both flat panels and very deep parts.

* Faster clamping--Two new features contribute to dry cycles 2 sec faster than any other machine in this size range, according to Hertzer. First, each locking nut on the tiebars now has its own hydraulic actuator right at the split nut. Older 1000- and 1500-ton models had a single actuator on each side of the machine that operated the top and bottom nuts by means of connecting rods. That meant less precise timing and required more maintenance.

Second, redesigned hydraulic circuitry now allows tonnage decompression and unlocking the split nuts to overlap with cooling while the rapid-traverse cylinder holds the mold closed. Strickley points out that such a timesaving feature is not possible with clamping on the four tiebars.

* Improved ram seals--Also new is a special ram-seal arrangement that keeps dirt out of the system while keeping the ram centered and preventing metal-to-metal contact. A "wiper" plus two low-friction seals of PTFE filled with glass and molybdenum are said to prevent leaks, wear, and heat generation for extended life. The seals are energized by pressure from a rubber o-ring that reportedly is immune to compression set.

Beefed-up injection end

The Maxima series also boasts increased injection rates and screw speeds. The new 4400-tonner has two 854-oz injection units that each can shoot 11.5 oz/sec of PE and plasticate 1500 lb/hr of PE or 1100 lb/hr of PP.

Also new is an extra hole in the standard stationary platen to accommodate a second injector for hard/soft overmolding and two-color parts.

More operator-friendly

Milacron accommodated user requests by providing a much larger conical hole in the stationary platen to provide easier access to purgings and the nozzle tip. Milacron also moved the rapid-traverse cylinder back into the clamp area so that it does not extend into the injection area.

The hydraulic pumps are shielded so that sound levels reportedly are much lower at the operator station. New Maxima models also have more platform area for the operator and more room in the "cattrack" for mold utility lines.


For more information, enter PTDirect code at

Cincinnati Milacron Injection Molding Machines, Batavia, Ohio (513) 536-2000 * PTDirect: 152AH
COPYRIGHT 2005 Gardner Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2005, Gale Group. All rights reserved. Gale Group is a Thomson Corporation Company.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Close-Up: INJECTION MOLDING
Author:Naitove, Matthew H.
Publication:Plastics Technology
Date:Jun 1, 2005
Previous Article:Compounders: now you can monitor color inside the extruder!
Next Article:How to address cooling system woes.

Related Articles
Injection molding.
Tandem tools: new twist on stack molds for larger parts.
Injection molding: stress-free production of large car windows, in-mold painting, and an injection unit that applies pack and hold while accumulating...
Injection molding machines.
Injection molding.
Injection molding machines.
Spotlight on electric and multi-component machines.
Injection molding machines.
Injection molding.
Injection molding machines.

Terms of use | Privacy policy | Copyright © 2019 Farlex, Inc. | Feedback | For webmasters