Printer Friendly

How to thermoform top-quality IMD inserts.

* Wider adoption of in-mold decorating (IMD) for demanding industries like automotive, appliances, and consumer electronics will require thermoformers to have the right know-how and equipment. Making precisely formed film inserts is critical for applications with registered print or graphics or an automotive Class A surface.

"The preform shapes and defines the decorative part surface," comments Jeff Christensen, specialist at the In-Mold Applications Div. of Display Pack, a leading designer and former of IMD preforms. Inserts must fit snugly in the mold cavity and resist tendencies to degrade, wrinkle, thin out, or change color under the influence of heat and pressure during back-molding. Christensen says making IMD preforms requires expertise in films: inks, and thermoforming. Suitable equipment needs state-of-art temperature controls to precisely govern sheet-temperature profile, sheet sag material distribution, and registration accuracy.

Patrick Griffin, applications, specialist at Bayer Polymers, says male tools are preferable for making Class A preforms since they attract less dust that can become embedded in parts. Male tooling also minimizes film wrinkling in complex tool areas, Griffin says. He adds that an intimate interface between film and tool surface is necessary to get efficient heat transfer, so precise die-cutting of IMD inserts to fit the cavity is critical. He favors use of 3D matched-metal dies for this task.

Griffin also advises that films for inserts should have low stress levels and should be brought up to forming temperature in a controlled way for efficient evaporation of residual moisture and ink solvents. Uncontrolled emissions can impair gloss and create flaws in part surfaces, he notes.

Conventional vacuum forming equipment offers maximum registration accuracy of about [+ or -] 0.020 in., Griffin says. When tighter tolerances are required--e.g., for telecom devices, where the standard is [+ or -]0.005 in.--he recommends use of a specialized process that forms inserts with low-temperature, high-pressure air.

Dedicated IMD machine

Jacob Horev, v.p. of equipment supplier ZMD International, notes that registration accuracy is critical if logos, words, or symbols on the film insert are to end up at exactly the right spot on a repeatable basis. ZMD is offering a single-station vacuum former designed specifically for registered IMD inserts, which typically are made out of polycarbonate films.

ZMD's model V-222DHCG and V-223DHCG machines have forming areas of 24 x 24 and 24 x 36 in., respectively, and use 58 to 87 independently controlled heat zones on both top and bottom. Horev reports strong sales of these machines for IMD of cellular phone housings, cameras, appliance controls, membrane switches, and woodgrain interior automotive panels.

One prerequisite for registered IMD inserts is excellent control of oven and sheet temperatures. The ZMD top heater platen can be adjusted up and down to increase sheet-temperature accuracy, while the bottom heaters provide a fast temperature rise to support the sheet and achieve near-zero sagging, Horev says. Oven temperature is controlled to [+ or -][degrees]F.

In conventional forming equipment, the heating cycle is governed by time, percent power, or sheet sag. ZMD monitors actual sheet temperature with noncontact infrared pyrometers that can "read" the temperature and then automatically initiate the forming cycle when the sheet reaches the target temperature.

Precise temperature control of molds is critical to controlling shrinkage of inserts. Every 5[degrees] F variation in mold temperature can cause a 0.001 in./in, change in shrinkage.

ZMD's machines also minimize distortion of printed graphics by keeping the clamp frame stationary during the heating cycle while moving the heater platens, thus all but eliminating sag. Horev says excessive sag is a major cause of image distortion. In addition, a four-way adjustable pneumatic clamp frame reportedly allows easy setting of sheet position for registration within [+ or -]0.005 in.

LEARN MORE online

Visit www.plasticstechnology.com/articles/200402cu.html for a link to this related articles:

* Where the Action Is: Decorating with Formable Films, January '04

NEED TO KNOW MORE?

Bayer Polymers, Pittshurgh (800) 652-2927, www.bayerone.com

DisplayPack, Grand Rapids, Mich. (616) 451-3061, www.displaypack.com

ZMD International, Long Beach, Calif. (800) 959-0998, www.zmd.com
COPYRIGHT 2004 Gardner Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2004, Gale Group. All rights reserved. Gale Group is a Thomson Corporation Company.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Thermoforming
Author:Leaversuch, Robert
Publication:Plastics Technology
Date:Feb 1, 2004
Words:671
Previous Article:Composites show introduces reinforcements, fillers & additives.
Next Article:Get the most from flow simulation.


Related Articles
Try in-mold decorating for good looks that last.
Thermoforming shines in exterior vehicle panels. (Thermoforming: Close-Up).
Forming process for IMD is available for license. (Auxiliaries).
Why all eyes are on in-mold decorating.
Decorating with formable films.
Thermoforming goes paint-free, too.
Paint-free color conference.
35 In-mold decorating & labeling.
Thermoformer offers help with IMD.

Terms of use | Privacy policy | Copyright © 2019 Farlex, Inc. | Feedback | For webmasters