Printer Friendly

Grab&go tool storage.

Do you spend too much time looking for tools on shelves scattered around your garage? If so, this grab-and-go tool cabinet is the answer. You corral all your power tools and accessories in one place and roll them around your garage or shop. The pullout table is great for doing quick repairs, prepping tools and sorting parts. The drawers are removable totes that you can carry to your work area.

[ILLUSTRATION OMITTED]

You'll also like how easy it is to build. All the parts are glued and screwed together with simple butt joints and overlays. Just build the top section of tool bins first, then build the lower shelving unit to slide under.

Time, money & materials

You can easily build the cabinet in one weekend and then apply the finish and install the hardware the next. Figure on spending about $375 for the entire project including hardware and finish. We chose 3/4-in. birch plywood for the main structure and 1/2-in. plywood for the backs and drawer sides. You'll also need hardwood for the drawer fronts and the edges of the pullout work surface. You can dress up the look with simple moldings to cover the exposed plywood faces.

Build the upper bins first

[ILLUSTRATION OMITTED]

Cut the plywood parts according to the Cutting List on p. 48. Assemble each of the three bins as shown in Photo 1. To make assembly faster, we used self-drilling screws, which means you won't need a pilot hole or a countersink. However, drill a shallow starter hole with a 3/32-in. bit to keep the tip of the screw from wandering off the mark as you start to drive the screw.

When you join the three bins (Photo 2), you'll need a work surface that's absolutely flat; an old flush panel door on sawhorses works perfectly for this. Finish the bin unit by gluing and nailing the top into place (Photo 3).

[ILLUSTRATION OMITTED]

MEET A PRO

David Radtke

David is a custom cabinetmaker, home design consultant, freelance editor and home restoration specialist in Minneapolis. He enjoys archery, bowmaking, woodturning and cycling--whenever he's not standing behind a table saw or sitting in front of the drawing board.
Materials List

                  ITEM                  QTY.

3/4" hardwood plywood                  4
1/2" hardwood plywood                  2
1/4" x 3/4" screen molding             40'
1/4" x 1-1/2" lattice                  20'
3/4" x 1-1/2" (hardwood table edging)  5'
1 x 8 hardwood (drawer facing)         5'
1 x 4 hardwood (table front)           5'
14" ball-bearing drawer slides         2
3" swivel casters                      4
5" drawer pulls                        3
8"-wide drawer pulls                   2
Wood glue                              1 pint
No. 8 x 1-1/4" screws                  1 box
No. 8 x 1-1/2" screws                  1 box
5/16" x 1-1/2" lag screws              16
1-1/4" 18-gauge nails                  1 box
7/8" pneumatic staples                 1 box

Cutting List

KEY  QTY.     SIZE & DESCRIPTION

A    6     3/4" x 15-3/8" x 21" bin  N    3  3/4" x 6-5/8" x 19-1/4"
           sides                             hardwood drawer face

B    6     3/4" x 15-3/8" x 18" bin
           shelves

C    3     3/4" x 5" x 18" upper     P    2  3/4" x 3-1/2" x 15-3/4"
           bin shelves                       plywood side base
                                             supports

D    1     3/4" x 7" x 60-3/4" top

E *  1     1/2" x 21" x 58-1/4"      Q *  2  3/4" x 3-1/2" x 51-3/16"
           upper assembly back               plywood front and back
                                             base supports

F    2     3/4" x 15-3/8" x 32"      R    2  3/4" x 15-7/8" x 55-7/8"
           lower unit sides                  plywood finished sides

G *  3     3/4" x 15-3/8" x 56-7/8"  S *  1  3/4" x 14-5/8" x 54-3/8"
           lower unit shelves                plywood pullout table

H    1     3/4" x 15-3/8" x          T *  1  3/4" x 3-1/4" x 58-1/4"
           14-13/16" lower unit              hardwood table face
           vertical partition

J *  1     1/2" x 32" x 58-1/4"      U*   2  3/4" x 1-1/2" x 15-3/8"
           lower unit back                   hardwood table side
                                             edging

K    6     1/2" x 15-3/8" x 5-1/4"   V *  1  3/4" x 1-1/2" x 54-3/8"
           drawer sides                      hardwood table back
                                             edging

L *  6     3/4" x 17" x 5-1/4"       W    2  3/4" x 2" x 15-3/8"
           drawer fronts and backs           plywood spacers

M *  3     1/4" x 15-3/8" x 17-7/8"
           plywood drawer bottoms

* Measure and cut to fit


Making the drawers fit

Measure the openings in the bottom of the bins and then downsize the drawer about 1/8 in. in total height and width. Since the drawers don't have slides, this will give you just the right clearance. Take into account the thickness of the plywood drawer bottom. Sometimes "1/4-in. plywood" is actually 3/16 in. thick.

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

Build the lower shelving section

Measure the width of the top assembly and then cut the parts for the lower shelving unit so it'll be exactly the same width. "Three-quarter-inch" plywood isn't exactly 3/4 in. thick; it's actually 23/32 in. That's why it's critical to measure. Use the Cutting List as a guide, but measure carefully to be sure.

Screw the sides to the shelves using Figure A as your guide. Install the lower partition (H) halfway between the bottom and middle shelf. Cut the 1/2-in. plywood back and check the assembly for square, then glue and nail it to the back of the sides and shelf.

To reinforce the bottom shelf, rip 3-1/2-in. strips of 3/4-in. plywood (parts P and Q) and glue and nail them to the bottom of the assembly. Screw the casters to the strips.

Combine the two sections

Mount the drawer slide that will support the pullout table (Photo 5). Then lay the upper unit onto its back and glue and screw the outer sides (R) to the bin sides (A). You may need to shim underneath to bring the sides perfectly flush.

Next, slide the lower unit into the upper until it contacts the spacers (W). Align the faces of the lower assembly with the outer sides (R) and drive the screws from the inside. You'll need nine screws per side.

At this stage, the project has acquired considerable heft, so get someone to help you tip it upright.

Nail on the edging

Now you can cut and glue the edge banding to the exposed plywood edges. We used screen molding for the 3/4-in. faces and l/4-in.-thick lattice for the double-thick faces. You may need to rip the lattice to fit. Keep in mind that you don't want the trim to hang over and obstruct the drawer openings, so be sure to flush the edging with the plywood.

Finishing touches

With the unit nearly finished, you can now make the pullout table. Carefully measure the distance between the side spacers. Subtract 1 in. from this measurement (1/2-in. clearance for each drawer slide) and build the table to this precise width. Now you can cut and screw the drawer faces to the front of the drawers. Be sure you have 1/4-in. clearance between the bottom of the drawer faces and the pullout table. Align the edges of the outer drawer faces so they're even with the table front.

For a fast, easy finish, use a wipe-on polyurethane or Watco oil. Use a brush to get into tight areas and then a lint-free rag to wipe the finish. Let dry and give it a second coat.

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

* familyhandyman.com

* Build a big workbench that fits in a small space. Search for "folding workbench."

* Search for "knockdown workbench" to find four easy-to-store designs.

* Need more outlets in your shop? Search for "surface wiring" to see how to do it without tearing into walls.

* Pack more storage into a crowded workshop. Search for "small-shop storage."

tip

To make sure your drawers don't get trapped inside their openings before you install the fronts, press a strip of masking tape onto the inside front of the drawer and let it hang past the drawer. You can pull on the tape if you accidentally close the drawer.

by David Radtke

editors@thefamilyhandyman.com
COPYRIGHT 2010 Home Service Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2010 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:THE TOTALLY TOOLS ISSUE
Author:Radtke, David
Publication:The Family Handyman
Geographic Code:1USA
Date:Nov 1, 2010
Words:1385
Previous Article:Get knives sharp! & keep 'em sharp.
Next Article:Low water pressure.
Topics:

Terms of use | Copyright © 2017 Farlex, Inc. | Feedback | For webmasters