Printer Friendly

Fill Based on Volume, Not Weight.

Most parts should be 90-99% full after first-stage-by volume not weight. Here's why that's important and how to make a first-stage-only part.

When processing via "Scientific Molding," injecting plastic into the mold or cavity is separated into two stages: filling (or "first stage") and pack-and-hold ("second stage"). During the last few weeks I've been getting lots of emails and have had several discussions focusing on just how full the part should be at the end of first stage. And since we call for a greater than 90% full part at the end of first stage, does this mean by weight or by volume? Good questions. Where do we find the answers?

To start let's define the terms, since there are host of different names, labels, or expressions for first and second stages. Terms such as fill, pack, hold, high-pressure, low-pressure, V-to-P, etc. have been used. Do they all mean the same thing or are there differences? Having numerous terms that are not clearly defined drives me to near insanity. It makes communications difficult, breeds misunderstanding, and confusion, and makes training especially difficult. So, to be clear on what I mean by first and second stage, see Fig. 1, which is an Injection Pressure (plastic pressure) vs. Time graph depicting first and second stage. This graph is typical for most but not all injection molding processes. (It would not apply, for example, to micro-molding, where the parts are too small to separate first stage from second stage.) In short, first stage fills the part to greater than 90% full, and second stage packs out the part with the remaining amount of plastic needed to finish filling the part, remove sinks, and provide the appropriate part dimensions.

Next let's cover the procedure to make a first-stage-only part. The goal is to make a short shot that is greater than 90% full. Seems simple enough; after all, the instructions to make a first-stage-only part is to take off second stage. Problem is, there are three different ways to take off second stage:

1. Take the second-stage timer to zero.

2. Take second-stage pressure to a very low value. I suggest 5 to 50 psi (0.5-3.5 bar) and leave at least 0.50 sec or longer on the second-stage timer.

3. Take second-stage timer to zero and reduce pressure to a low value.

Try each one ... my bet is you will not produce the same first-stage-only part. So, which one is best? I suggest the second approach, and let me explain why. There is the issue of momentum or over-travel on most molding machines. That is, the screw does not stop at the set cutoff position. It is critical that the processor sees, understands and deals with this over-travel in developing first stage. Also, it is critical that the processor ensures that this first-stage-only part is done under conditions where injection or first stage is not pressure limited. Many go with 10% higher set or available pressure vs. actual peak pressure during injection. I find this common rule of thumb to be inadequate.

So now that we know the procedure for making a first stage part, how full should it be? No easy answer here. Somewhere between 90 to 99.9% full--based on volume, not weight. Factors that influence this are the type of part, number of cavities, balance of filling, a weld line at the end of fill, a living hinge, etc. Bottom line for 99% of parts being molded: The first-stage part(s) should be visibly short, not full with sink. But why by volume and not weight?

The emails and blogs I've received and read covered a variety of rationales for volume or weight, dealing with melt density vs solid density, sinks, bounce-back, and other factors. For me, the answer--volume--comes from studying cavity-pressure curves and witnessing the wear on parting lines along with the resulting development of flash on parts.

Figure 2 provides the injection-pressure curve in first and second stage, along with an end-of-cavity pressure curve for a first stage developed by weight. Note the rapid, near-vertical instant rise of cavity pressure. This is a significant force on the mold's parting line and will likely prematurely wear it, leading to flash at some point.

Figure 3 provides the injection-pressure curve for first and second stage, along with an end-of-cavity pressure curve for a first stage developed by volume. Note the rounded end-of-fill cavity-pressure curve. It suggests less stress is being generated on the parting line allowing it to withstand significantly more shots before wear and subsequent development of flash. Please understand there are a number of factors that influence parting line wear; this is only one of several. Also, the shape of an end-of-fill cavity-pressure curve is part-dependent.

In short, develop first stage with time on the second-stage timer and based on volume. It should provide less wear on the parting line.


Learn more at

Get more insights on injection Molding from our expert authors:

John Bozzelli is the founder of Injection Molding Solutions (Scientific Molding) in Midland, Mich., a provider of training and consulting services to injection molders, including LIMS, and other specialties. Contact;

Caption: FIG 1 First and Second Stage

Caption: FIG 2 First Stage by Weight

Caption: FIG 3 First Stage by Volume
COPYRIGHT 2018 Gardner Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2018 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Author:Bozzelli, John
Publication:Plastics Technology
Date:Aug 1, 2018
Previous Article:A Processor's Most Important Job: PART 7.
Next Article:Why Ejector Pins Break ... and How to Prevent It: PART 1: In part one of this four-part series, we focus on the molding machine and the ejection...

Terms of use | Privacy policy | Copyright © 2021 Farlex, Inc. | Feedback | For webmasters