Printer Friendly

Development and validation of method for the determination of organochlorine pesticides and trihalomethanes in the water by HRGC-ECD/Desenvolvimento e validacao de metodo para a determinacao de pesticidas organoclorados e trihalometanos em agua usando HRGC-ECD.


Organochlorine pesticides and trihalomethanes are chemical substances presenting health and environmental risks; therefore, their levels of concentration in drinking and surface water must be monitored. In Brazil, there are two regulations that establish acceptable levels: Ministry of Health regulation no 518/2004, specifically for the control and monitoring of organochlorine pesticides and trihalomethanes in drinking water, and regulation no 357/2005, from Conama, the National Environmental Council, which establishes maximum levels for organochlorine pesticides in surface water.

Organochlorine pesticides (OCP) are synthetic chemicals and are among the most persistent pollutants in aqueous environments (BAIRD, 2002). Due to their chronic persistence and bioaccumulation, they have been banned or restricted for some applications, and most of them have been included in the list of priority pollutants in many countries. Several studies have shown that organochlorine pesticides have deleterious effects on the immune system and increased amounts have been detected in certain cancerous tissues (KRIEGER et al., 1994). Organochlorine pesticides have been reported as possibly responsible for stimulating the development of breast cancers in women (FALCK et al., 1992) and in male mice normally resistant to breast cancer (DAVIS et al., 1993). The risk of breast cancer has been related to the possible interaction between organochlorine pesticides and estrogen receptors (JAGA, 2000).

In Brazil, the Ministry of Agriculture also regulates the registration of active ingredients for various uses in agriculture. The use of organochlorine pesticides has been restricted since 1986. However, four active principles from this pesticide group are still registered in Brazil. These are dicofol, endosulphan, methoxychlor and lindane. Dicofol and endossulfan are still used on cotton, coffee, soy bean, citrus and apple crops. Besides the use of allowed organochlorine pesticides, forbidden organochlorine pesticides are still commonly smuggled into Brazil, demonstrating the importance of evaluating these compounds in surface and drinking water and in the entire environment.

Other chemical compounds detected in drinking water and as dangerous to the health as organochlorine pesticides are trihalomethanes (THM). Trihalomethanes are represented by chloroform (CH[Cl.sub.3]), dichlorobro mo methane (CH[Cl.sub.2]Br), chlorodibromomethane (CHCl[Br.sub.2]) and bromoform (CH[Br.sub.3]). The formation of THM in drinking water results from the reaction of chlorine with naturally occurring organic matter present in surface water, mainly humic and fulvic acids. The Brazilian drinking water quality standard for total trihalomethanes (THM) is 100 [micro]g [L.sup.-1]. Chlorine is applied to drinking water in order to deactivate microorganisms and/or to ensure a residual concentration in drinking water distribution system avoid the development of microorganisms. It has traditionally been a preferred disinfecting agent due to its effectiveness and relatively low price (RODRIGUEZ; SERODES, 2001).

The presence of chlorinated disinfection byproducts (DBP), especially THM, in drinking water is of concern from a public health standpoint, because they are suspected to be carcinogenic (TOKMAK et al., 2004). Several studies have suggested that there are increased risks of bladder, stomach, large intestine, and rectal cancer in areas where chlorinated surface waters have been used (LEE et al., 2001).

Organochlorine pesticides and THM are present in water at residual levels. Sample preconcentration is necessary for later chromatographic analysis. Several methods for the determination of organochlorine pesticides and THM in water have been developed and reported in the literature, such as liquid-liquid extraction: LLE; purge-and-trap: PAT (DIAMADOPOULOS et al., 1998) direct aqueous injection: DAI; and headspace: HS (CASTELLO et al., 1986). Goufinopoulos et al. (2001), verified that HS and PAT were more sensitive than DAI e LLE. The advantages of utilizing HS or PAT include minimal sample preparation, reproducibility, reduced analysis times using an automated system, and the possibility of on-line coupling to a GC. However, disadvantages include matrix effects for HS and the higher prime cost and carryover problems with PAT (FATOKI; AWOFOLU, 2003).

In addition to LLE, solid phase extraction (SPE) has been used to analyze organochlorine pesticides in surface water, generally with cartridges packed with silica sorbents modified with octadecylsilyl. This technique uses a smaller amount of solvent and is less laborious than conventional liquid-liquid extraction. However, disadvantages include significant background interference and poor reproducibility (CASTELLO et al., 1986).

An advantage of solid phase micro extraction (SPME) for organochlorine pesticide extraction in water samples is the absence of solvent, and excellent sensitivity and reproducibility (GOLFINOPOULOS et al., 2001). However, the fibers are fragile and expensive, and some pesticides, such as DDT and endrin, suffer thermal decomposition inside the fibers.

A new extraction technique based on the same extraction principles as SPME was developed (BALTUSSEN et al., 1999). A stir bar is coated with the sorbent polydimethylsiloxane (PDMS). This technique is known as stir bar sorptive extraction (SBSE) and the coated stir bars are sold under the Twister name. However, this method is difficult to apply in routine analysis.

Liquid-phase micro-extraction is an emerging extraction technique with applications in biomedical, environmental and food analysis (PSILLAKIS; KALOGERAKIS, 2003). LPME uses a hollow polypropylene fiber which is impregnated with microliters of a nonpolar solvent (toluene, n-hexane, dichloromethane or isooctane) and connected to a microsyringe. Later, the solvent along with the dissolved analytes is sucked into the microsyringe, for chromatographic analysis. LPME is a more reproductive technique than SPME. It requires smaller amounts of solvent, but to achieve highly efficient extractions, the analytes must present low water solubility, low volatility and high stability in the fiber pores. Direct LPME has not been reported in the literature for THM analysis. However, Zhao and Lee (2001), had good THM recovery using headspace coupled with LPME (HSLPME) with limits of detection (LOD) ranging from 0.15 to 0.4 [micro]g [L.sup.-1].

Liquid-liquid extraction (LLE) is the most commonly used method for water sample preparation. EPA Method 508 and EPA Method 551.1 are official methods for analyzing organochlorine pesticides and THM, respectively, and may be carried out manually by shaking the water sample and an organic solvent in a separation funnel, or automatically with a continuous liquid-liquid extractor. EPA Method 508 uses methylene chloride as an extraction solvent, EPA Method 551.1 uses methyl-ieri-butyl ether (MTBE) and pentane to extract THM and five organochlorine pesticides in drinking water samples, with manual shaking.

Dichloromethane needs to be removed in evaporation stages, however, and this may overload the electron capture detector. Moreover, many extraction stages increase the possibility of sample contamination and make the process slow and tedious.

Having analyzed the advantages and the disadvantages of each extraction method available for the analysis of THM and organochlorine pesticides in water samples, we now propose a simple and inexpensive automated liquid-liquid extraction technique which can be applied in routine analyses of water quality.

Material and methods


Organochlorine pesticide analytical standards Lindane (99%), Aldrin (99%), Dieldrin (99%), Endosulphan (96.6%), Endrin (77.3%), o,p'-DDT (99%), DDD (72.9%), p,p'-DDE (99%) and Metoxychlor (99%) were purchased from PolyScience (Niles, IL, USA). Mirex (99%), a-chlordane (99%), Xchlordane (99%) and hexachlorobenzene (HCB) (99%) were EPA standards.

Standard solutions of 200 mg [L.sup.-1] of THM in methanol, including chloroform (CH[Cl.sub.3]), bromodichloromethane (CH[Cl.sub.2]Br), dibromochloromethane (CHCl[Br.sub.2]) and bromoform (CH[Br.sub.3]), were purchased from AccuStandard[R] (New Haven, USA).

Hexane and acetone for ultra resi-analysed[R] and Absolv[R] were obtained from J.T. Baker[R] and Tedia[R], respectively. Sodium chloride was purchased from Mallinckrodt Baker (Xalostoc, Edo. de Mex, Mexico). Ultrapure water was prepared by purifying demineralized water using a Milli-Q filtration system (Millipore, Bedford, USA).

Stock and spiking solutions

Stock solutions of organochlorine pesticides were prepared in hexane (10.0 mg [L.sup.-1]). These solutions were diluted as required to prepare intermediate stock solutions. Solutions to obtain the calibration curve were prepared by dilution of working solutions in the following concentrations: aldrin and dieldrin (0.24 - 0.36 [micro]g [L.sup.-1]), o,p'-DDT, DDD, p,p'-DDE and Lindane (16 - 24 [micro]g [L.sup.-1]), Methoxychlor and Endosulphan (160 - 240 pg [L.sup.-1]), Endrin (4.8 - 7.2 pg [L.sup.-1]), Hexachlorobenzene (8.0 12 [micro]g [L.sup.-1]), Mirex (0.8 - 1.2 [micro]g [L.sup.-1]), [alpha]-chlordane and X-chlordane (1.6 - 2.4 pg [L.sup.-1]).

Acetone was used to prepare the spiking stock solutions of pesticide standards (10.0 mg [L.sup.-1]) to contaminate ultrapure water. Aliquots of the spiking stock solutions were diluted to prepare intermediate spiking solutions in acetone in their final concentration. Aliquots collected to prepare working calibration standards used in LLE experiments were around 100 [micro]L. All of these stock and spiking solutions were stored in a freezer.

The solutions to obtain the THM curve calibration were prepared by diluting the stock solution in hexane at concentrations that varied around the limit of detection (LOD) for each THM and 1,500 [micro]g [L.sup.-1].

Liquid-liquid extraction procedure

The liquid-liquid extraction was performed using a basic VXR model IKA[R] Vibrax[R] orbital shaker, with a 21 mm-diameter test tube attachment. A water sample aliquot (20 mL) was transferred to a test tube fitted with a stopper. Prior to the extraction, 3% (w [v.sup.-1]) sodium chloride was added to all water samples. The extraction was carried out after adding an aliquot of hexane (2 mL) by shaking the test tube at 1,400 rpm for 2h. The phases were then allowed to separate and the organic layer was analyzed by HRGC-ECD.

Extraction efficiency

OCP was extracted by the LLE method by spiking OCP standards in ultrapure water at five levels of concentration. Water samples (100 mL) were spiked with solutions of pesticides in acetone in concentrations as shown in Table 1. The ratio of the amount of OCP recovered from spiked water samples to the amount added to spike was used to calculate OCP recovery in fortified water samples, based on the ratio of the peak areas of the standards to the working calibration solution with the same concentration.

Some parameters were evaluated to improve extraction efficiency, such as the effects of adding NaCl to the samples and the time of extraction. The concentration of pesticides for this evaluation was the maximum allowed by Brazilian legislation.

For THM extraction efficiency studies, the best extraction time and NaCl content parameters for organochlorine pesticides were selected. Concentration levels to evaluate THM recovery were 50, 75, 100, 125 and 150 [micro]g [L.sup.-1].


Chromatographic analysis of organochlorine pesticides and trihalomethanes was performed on a Hewlett-Packard 6890 Series Gas Chromatograph equipped with a [sup.63]Ni electron capture detector (ECD) system. A HP-5 capillary column (Agilent Technologies) and cross linked 5% phenyl methyl siloxane, 30 m x 0.25 mm I.D. x 0.25 pm, were used for all investigations. The injector was used in pressure-pulsed splitless mode. Purge flow to split vent and injection pulse pressure were evaluated. The injector and detector were kept at 220[degrees]C and 300[degrees]C, respectively. The oven temperature was initially 40[degrees]C and was then increased at 20[degrees]C [min..sup.-1] to 190[degrees]C and kept at this temperature for 7 min.; following this, the temperature was ramped at 20[degrees]C [min..sup.-1] to 220[degrees]C and was held for 5 min., and finally a third ramp to 280[degrees]C at 30[degrees]C [min..sup.-1] was applied, with the final temperature held for 3 min. 1 [micro]L aliquots were injected manually with a microsyringe.


Results and discussion

Chromatographic analysis

The Figure 1 shows the chromatographic profile obtained for THM and OCP after liquid-liquid extraction of water samples spiked with OCP and THM standards at the maximum concentration level allowed by Brazilian legislation (level three, as shown in Table 1). The chromatogram shows good separation of the analytes with acceptable analysis time and good sensitivity, demonstrating that the chromatographic conditions are excellent for the separation and simultaneous determination of THM and OCP.

Optimization of LLE conditions

Salting-out effect

The effect of added NaCl in the recovery efficiency of organochlorine pesticides in water samples was investigated, with results shown in Figure 2. The o,p'-DDT, p,p'-DDE and hexachlorobenzene showed better extraction efficiency in an NaCl concentration of 1% (w [v.sup.-1]). Aldrin did not present good extraction at NaCl concentrations lower than 10% (w [v.sup.-1]). An increase in saline concentration did not affect the extraction of dieldrin. Endrin, a-chlordane, X-chlordane, mirex, endosulphan, metoxychlor, lindane and DDD showed better extraction in NaCl concentrations of 3% (w [v.sup.-1]). Thus, the concentration of NaCl used in the experiments was 3% (w [v.sup.-1]) because it allowed acceptable extraction yield for most analytes.


Extraction time

The Figure 3 shows the peak area obtained by HRGC-ECD for OCP as a function of extraction time. This evaluation shows that the majority of the analytes present a constant peak area in extraction time of 30 min., and these values have practically no variation when extraction time is increased, except for aldrin, which is extracted in higher amounts from water samples when the extraction time increases.

The Table 2, which presents OCP recovery as a function of extraction time, shows that in 30 min., most analytes presented satisfactory recovery, except for aldrin and dieldrin. Considering that Brazilian legislation still allows aldrin to be used under certain conditions, pesticide recovery was also evaluated over longer extraction times in an attempt to improve the extraction of aldrin and dieldrin.


With an increase in extraction time to 120 min., aldrin and dieldrin were extracted at higher levels. When the extraction time was increased to 180 min., the recovery levels decreased again. This was also observed for other OCPs. Mirex always demonstrates a reduction in recovery with an increase in extraction time.

Thus, the extraction time that promoted the best recovery of the analytes in water was 120 min., with recovery ranging of 50.0% for aldrin and 116.5% for lindane. The relative standard deviation (RSD) varied between 1.6% for DDD and 16.8% for aldrin. These results demonstrate that this extraction method appears to promote acceptable recovery with good repeatability.

The efficiency and accuracy of the extraction method under discussion was also evaluated using quality parameters such as linearity, precision and sensibility. Under optimum conditions, linearity, limit of detection, limit of quantitation and repeatability data were obtained and shown in Table 3.

All organochlorine pesticides exhibited good linearity with correlation coefficients (r) of 0.99072-0.99905. This allowed the quantitation of these compounds by the external standardization method.

Limits of detection (LOD) of the OCP, calculated on the basis of the signal to noise (s/n) ratio of 3 in HRGC-ECD measurements, were in the range of 0.0027-0.0470. The limit of quantitation (LOQ) was established as the lowest concentration that has a relative standard deviation of 20% and varied between 0.0059 [micro]g [L.sup.-1] for a-chlordane and 0.1400 [micro]g [L.sup.-1] for lindane. Repeatability was evaluated by extracting aqueous sample spiked at five levels of concentration for each OCP with three replicates. The relative standard deviations (RSD) were acceptable, ranging from 0.056 to 11.000%.

THM analysis

The same optimized extraction conditions obtained for organochlorine pesticides were used for trihalomethanes analysis. THM extraction efficiency was evaluated as shown in Table 4, which indicates that mean recovery varied from 78.9% for CH[Cl.sub.3] to 93.2% for CH[Br.sub.3]. All THMs exhibited good linearity with correlation coefficients (r) of 0.99423-0.99949, allowing the quantitation of these compounds by external standardization.

Limits of detection (LOD) for THM, calculated on the basis of the signal to noise (s/n) ratio of 3 in HRGC-ECD measurements, were in the range of 0.018 - 0.260 [micro]g [L.sup.-1]. The relative standard deviations (RSD) were in the range of 1.9 - 3.4%, demonstrating that the method possesses high sensitivity and good repeatability.


This paper demonstrates the successful development and application of an automated liquid-liquid extraction method. The method exhibits good precision, reproducibility and linear response over a wide concentration range, demonstrating the possibility of simultaneous determination of trihalomethanes and OCP by high resolution gas chromatography. The method allows fast and easy sample preparation for routine analysis, without extract evaporation stages or sample cleanup. This reduces problems of interference over many stages of sample manipulation. Due to the automation of the extraction and the use of small amounts of solvent, the exposure of the analyst to toxic solvents was avoided. Moreover, the method is not tedious, and it is possible to prepare up to sixteen samples simultaneously. Thus, the method developed is viable, fast and low cost for routine analysis of trihalomethanes and organochlorine pesticides in water by trace analysis and water quality control laboratories. DOI: 10.4025/actascitechnol.v32i4.7689


The authors are grateful to FINEP and Capes for financial support.


BAIRD, C. Quimica ambiental. Porto Alegre: Bookman, 2002.

BALTUSSEN, E.; SANDRA, P.; DAVID, F.; CRAMERS, C. Stir bar sorptive extraction (SBSE), a novel extraction technique for aqueous samples: Theory and principles. Journal of Microcolumn Separations, v. 11, n. 10, p. 737-747, 1999.

CASTELLO, G.; GERBINO, T. C.; KANTIZ, S. Sensitivity and linearity of headspace and liquid-liquid-extraction techniques for gas-chromatographic analysis of halocarbons in water. Journal of Chromatography A, v. 351, n. 2, p. 165-75, 1986.

DAVIS, D. L.; BRADLOW, H. L.; WOLFF, M.; WOODDRUFF, T.; HOEL, D. G.; ANLON-CULVER, H. Medical hypotethesis: xenoestrogens as preventable causes of breast cancer. Environmental Health Perpect, v. 101, n. 5, p. 372-377, 1993.

DIAMADOPOULOS, E.; SAKELLARIADIS, D.; KOUKOURAKAI, E. The effect of humic acid on the transport of volatile chlorinated hydrocarbons in soil. Water Research, v. 32, n. 11, p. 3325-3330, 1998.

FALCK, F.; RICCI, A.; WOLFF, M. S.; GODBOLD, J.; DECKERS, P. Pesticides and polychlorinated biphenyl residues in human breast lipids and their relation to breast cancer. Archives of Environmental Health, v. 47, n. 2, p. 143-146, 1992.

FATOKI, O. S.; AWOFOLU, R. O. Methods for selective determination of persistent organochlorine pesticide in water and sediments by capillary gas chromatography and electron-capture detection. Journal of Chromatography A, v. 983, n. 1-2, p. 225-236, 2003.

GOLFINOPOULOS, S. K.; LEKKAS, T. D.; NIKOLAOU, A. D. Comparison of methods for determination of volatile organic compounds in drinking water. Chemosphere, v. 45, n. 3, p. 275-284, 2001.

JAGA, K. What are the implications of the interaction between DDT and estrogen receptors in the body? Medical Hypotheses, v. 54, n. 1, p. 18-25, 2000.

KRIEGER, N.; WOLFF, M. S.; HIATT, R. A.; RIVERA, M.; VOGELMAN, J.; ORENTREICH, N. Breast cancer and serum organochlorines: a prospective study among White, Black and Asiban women. Journal of the National Cancer Institute, v. 86, n. 9, p. 589-599, 1994.

LEE, K. J.; KIM, B. H.; HONG, J. U.; PYO, H. S.; PARK, S.; LEE, D. W. A study on the distribution of chlorination by-products (CBPs) in treated water in Korea. Water Research, v. 94, n. 12, p. 47-56, 2001.

PSILLAKIS, E.; KALOGERAKIS, N. Developments in liquid-phase microextraction. Trends in Analytical Chemistry, v. 22, n. 10, p. 565-574, 2003.

RODRIGUEZ, M. J.; SERODES, J. B. Spatial and temporal evolution of trihalomethanes in three water distribution systems. Water Research, v. 35, n. 6, p. 1572-1586, 2001.

TOKMAK, B.; CAPAR, G.; DILEK, F. B.; YETIS, U. Trihalomethanes and associated potential cancer risks in the water supply in Ankara, Turkey. Environmental Research, v. 96, n. 3, p. 345-352, 2004.

ZHAO, L.; LEE, H. K. Application of static liquid-phase microextraction to the analysis of organochlorine pesticides in water. Journal of Chromatography A, v. 919, n. 2, p. 381-388, 2001.

Received on July 14, 2009.

Accepted on September 1st, 2009.

License information: This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Maria Isabel Ribeiro Alves * and Nelson Roberto Antoniosi Filho

Laboratorio de Metodos de Extracao e Separacao, Instituto de Quimica, Universidade Federal de Goias, Cx. Postal 131, 74001-970, Goiania, Goias, Brazil. * Author for correspondence. E-mail:
Table 1. Concentration levels of water samples spiked with
organochlorine pesticides for recovery studies.

Pesticides          Concentration levels ([micro]g [L.sup.-1])

                      1       2       3       4       5

Hexachlorobenzene    0.8     0.9     1.0     1.1     1.2
Lindane              1.6     1.8     2.0     2.2     2.4
Aldrin              0.024   0.027   0.030   0.033   0.036
X-chlordane         0.16    0.18    0.20    0.22    0.24
Endosulphan          16      18      20      22      24
a-chlordane         0.16    0.18    0.20    0.22    0.24
Dieldrin            0.024   0.027   0.030   0.033   0.036
p,p'-DDE             1.6     1.8     2.0     2.2     2.4
Endrin              0.48    0.54    0.60    0.66    0.72
DDD                  1.6     1.8     2.0     2.2     2.4
o,p '-DDT            1.6     1.8     2.0     2.2     2.4
Metoxychlor          16      18      20      22      24
Mirex               0.08    0.09     0.1    0.12    0.14

Table 2. Mean recoveries and precision for OCP with the
proposed LLE method as a function of extraction time.

                         Extraction time

Pesticides      30 min.        120 min.        180 min.

                 Percentage of Recovery (RSD %) (a)

HCB           98.6% (7.6)     92.5% (6.6)     90.4% (4.4)
Lindane       100.0% (1.2)   116.5% (15.2)   118.1% (13.3)
Aldrin        29.9% (16.2)   50.0% (16.8)     39.0% (3.7)
X-chlordane   90.0% (6.1)    104.8% (4.4)     88.2% (8.8)
Endosulphan   85.1% (4.9)    110.6% (4.9)    108.3% (4.9)
a-chlordane   89.0% (5.2)    101.5% (8.9)     94.8% (7.9)
Dieldrin      27.6% (16.4)    64.8% (3.7)     63.5% (2.0)
p.p "-DDE     60.8% (2.5)     75.2% (4.7)     67.5% (5.6)
Endrin        94.4% (7.2)    110.4% (5.2)    110.3% (5.2)
DDD           84.3% (5.2)     90.1% (1.6)     82.8% (6.6)
o.p'-DDT      82.7% (12.1)    85.5% (5.8)     75.3% (4.4)
Metoxychlor   65.5% (4.7)    107.3% (8.7)    100.0% (6.4)
Mirex         74.4% (8.2)    60.8% (16.5)     46.6% (9.5)

(a) Obtained for five determinations.

Table 3. Linearity, precision and limits of detection and
quantitation for the analysis of OCP.

               Coefficient of    RSD (%)   LD ([micro]g   LQ ([micro]g
Pesticides     Correlation (r)     n=3     [L.sup.-1])    [L.sup.-1])

HCB                0.99602        2.200       0.0050         0.0150
Lindane            0.99496        2.100       0.0470         0.1400
U.S. Total         0.99867        0.099       0.0038         0.0077
A-chlordane        0.99083        0.056       0.0037         0.0095
Endosulphan        0.99905        6.800       0.0120         0.0300
a-chlordane        0.99368        0.380       0.0029         0.0059
Dieldrin           0.99072        0.260       0.0035         0.0087
p.p '-DDE          0.99644        2.680       0.0027         0.0067
Endrin             0.99675        0.860       0.0086         0.0170
DDD                0.99880        1.200       0.0035         0.0087
o.p "-DDT          0.99621        0.750       0.0030         0.0060
Methoxychlor       0.99564       11.000       0.0095         0.0190
Mirex              0.99195        0.150       0.0035         0.0070

Table 4. Recovery, linearity, precision, limits of detection
(LOD) and quantitation (LOQ) for the analysis of THM.

THM              Recovery (%) (r) (RSD)     Calibration Curve

CH[Cl.sub.3]      78.9 (11.6) 0.99949     [??] =1052.54x + 15.71
CH[Cl.sub.2]Br     87.5 (5.8) 0.99820     [??] =2745.67x + 65.41
CHCl[Br.sub.2]     88.1 (8.7) 0.99423     [??] =1728.85x + 61.21
CHBr3              93.2 (3.5) 0.99720     [??] =954.81x + 38.15

                 RSD (%)   LOD ([micro]g   LOQ ([micro]g
THM               (n=3)     [L.sup.-1])     [L.sup.-1])

CH[Cl.sub.3]       2.5         0.018           0.052
CH[Cl.sub.2]Br     1.9         0.26            0.39
CHCl[Br.sub.2]     2.8         0.035           0.052
CH[Br.sub.3]       3.4         0.86             1.3
COPYRIGHT 2010 Universidade Estadual de Maringa
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2010 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Author:Alves, Maria Isabel Ribeiro; Filho, Nelson Roberto Antoniosi
Publication:Acta Scientiarum. Technology (UEM)
Date:Oct 1, 2010
Previous Article:A study of the chemical and physical properties of cashew nut shell ash for use in cement materials/Estudo das caracteristicas quimicas e fisicas da...
Next Article:Allelopathic and antioxidant activity and total phenolic contents of Hydrocotyle bonariensis Lam. (Araliaceae)/Atividade alelopatica, antioxidante e...

Terms of use | Privacy policy | Copyright © 2021 Farlex, Inc. | Feedback | For webmasters |