Printer Friendly

Decolorization of methylene blue by Ag/SrSn[O.sub.3] composites under ultraviolet radiation.

1. Introduction

Strontium stannate (SrSn[O.sub.3]) is a type of AB[O.sub.3] perovskite, at which A is commonly an alkaline earth such as Ca, Sr, and Ba, and B is a p-block posttransition metal in the periodic table. AB[O.sub.3] perovskite has been used for energy conversion, lithium ion batteries, stable capacitors, oxygen-permeable ceramic membranes, and gas sensors [1-4]. In recent years, SrSn[O.sub.3] has been widely used in photocatalytic applications [4-6]. Development of semiconductors to enhance photocatalytic activity by being deposited with noble transition metals like Ag, Au, Pt, and Ir has been intensively investigated. The noble metal/semiconducting oxide composites are able to slow down the rate of electron-hole recombination, due to the better charged separation of electrons and holes. The electrons accumulated on the metal and holes remained on the photocatalytic surfaces [7]. Silver nanoparticles exhibit unexpectedly high photocatalytic activities toward different types of reactions compared to the bulk and promote the performance of photocatalysis [8].

SrSn[O.sub.3] has been synthesized by different methods such as solid state reaction at a temperature above 1,000[degrees]C [2], hydrothermal method [3, 4], microemulsion [9], and polymeric precursor method [10]. Recently, microwave radiation has been used for the synthesis of materials, including inorganic complexes, oxides, and sulfides. Microwave radiation has shown very rapid growth in its application to materials science and engineering due to its unique reaction effect, such as rapid volumetric heating and the consequent dramatic increase in reaction rate [11,12]. Silver nanoparticles can be deposited on substrates by polyol organic agent as a reducing agent in assisting the nucleation and growth of nanoparticles on a variety of substrates including silicon/carbon composite microspheres, polymer nanofibers, and Ti[O.sub.2] nanoparticles [13-15].

In the present research, a cyclic microwave radiation (CMR) used for the synthesis of rod-like SrSn[(OH).sub.6] precursors in surfactant-free solution with fast reaction time is reported. Metallic silver nanoparticles were doped with SrSn[O.sub.3] products to form Ag/SrSn[O.sub.3] composites, which are new candidates for photocatalysis for waste water treatment.

2. Experimental Procedures

To synthesize SrSn[(OH).sub.6] precursors, 0.005 mol strontium acetate ([(C[H.sub.3]C[O.sub.2]).sub.2]Sr) and 0.005 mol tin(II) chloride dihydrate (Sn[Cl.sub.2] * 2[H.sub.2]O) were dissolved in 80 mL deionized water with 30 min continuous stirring at room temperature. The pH was adjusted to 12 using 3 M NaOH with continuous stirring for 1 h until white suspension was obtained. The mixture was irradiated by a 180 W cyclic microwave radiation (1 min on for every 1 min interval) for 30 cycles. The white precipitates were synthesized, separated using a filtered paper, rinsed with deionized water for several times and absolute ethanol, and dried in air at 70[degrees]C for 24 h. In the end, the SrSn[(OH).sub.6] precursors were calcined in ambient atmosphere at 900[degrees]C for 3hto form the SrSn[O.sub.3] product.

To synthesize Ag/SrSn[O.sub.3] composites, 1 wt%, 5 wt%, and 10wt% AgN[O.sub.3] and 1g SrSn[O.sub.3] were dispersed in 50 mL of ethylene glycol (EG, [C.sub.2][H.sub.6][O.sub.2]) under magnetic stirring. The solutions were ultrasonically vibrated for 15 min to form products which were separated by filtering, washed with absolute ethanol, and dried in air at 70[degrees]C for 24 h to form Ag/SrSn[O.sub.3] composites. The final composites were labeled with 1 wt% Ag/SrSn[O.sub.3], 5 wt% Ag/SrSn[O.sub.3], and 10 wt% Ag/SrSn[O.sub.3].

The final products were characterized by an X-ray diffractometer (XRD, Philips X'Pert MPD) operating at 20 kV, 15 mA with Cu-K[alpha] line ([lambda] = 0.1542 nm) at a scanning rate of 0.02 deg/s over the 2[theta] range of 10-80 deg; X-ray photoelectron spectroscopy (XPS, Kratos Axis Ultra DLD) with a monochromatic Al Ka (1486.6 eV) radiation as the excitation source at 15 kV with spectrum calibration using a C1s electron peak at 285.1 eV; a Fourier transform infrared spectrometer (FTIR, Bruker Tensor 27) with KBr as a diluting agent operating in the range of 1000-400 [cm.sup.-1]; a scanning electron microscope (SEM, JEOL JSM-6335F) operating at 15 kV equipped with an Oxford Instruments INCA energy-dispersive X-ray (EDX) analyzer using Si(Li) as a detector; a transmission electron microscope (TEM, JEOL JEM2010) with a selected area electron diffractometer (SAED) operating at 200 kV; and a UV-visible spectrometer (Lambda 25 Perkin Elmer) using a UV lamp with the resolution of 2.0 nm. Photocatalytic activities of the products were investigated by studying the degradation of methylene blue (MB, [C.sub.16][H.sub.18][N.sub.3]SCl) dye in 100 mL 5.0 x [10.sup.-6] M MB aqueous solutions by 100 mg photocatalyst each. The solutions were stirred in the dark condition for 1h to establish an adsorption-desorption equilibrium of MB dye on the catalyst. Then, the solutions were irradiated by two 15 W UV lamps for different lengths of time for further analysis using the UV-visible spectrometer. The decolorization efficiency was calculated by

Decolorization efficiency (%) = [C.sub.o] - C/[C.sub.o] x 100, (1)

where [C.sub.o] and C were the initial and final concentrations of MB, respectively.

3. Results and Discussion

XRD patterns of different products are shown in Figure 1. The precursors were specified as hexagonal SrSn[(OH).sub.6] phase of the JCPDS database number 09-0086 [16]. Upon calcination of the precursors at 900[degrees]C for 3h, the products with high diffraction intensity and better crystalline degree were readily indexed to be orthorhombic perovskite structured SrSn[O.sub.3] of the JCPDS database number 77-1798 [16]. Then, SrSn[O.sub.3] products were doped with Ag nanoparticles to form Ag/SrSn[O.sub.3] composites. Comparing the patterns of the 1wt% Ag/SrSn[O.sub.3], 5wt% Ag/SrSn[O.sub.3], and 10 wt% Ag/SrSn[O.sub.3] composites to those of the JCPDS database number 09-0086 [16], they were still being identified as pure orthorhombic SrSn[O.sub.3] phase. No other peaks were detected in the XRD patterns of 1 wt% and 5 wt% Ag/SrSn[O.sub.3] composites. Possibly, concentration of Ag was too low to be detected. In case of 10 wt% Ag/SrSn[O.sub.3] composites, additional two peaks at 2[theta] of 38.50 and 77.84 deg were detected and specified as the (111) and (311) peaks of cubic Ag of the JCPDS database number 02-1098 [16], due to the reduction process [Ag.sup.+] [right arrow] [Ag.sup.0] by EG during ultrasonic vibration process. This detection indicated that Ag nanoparticles were only deposited on the SrSn[O.sub.3] surface. The average Ag particle size was estimated by Debye-Scherrer formula

D = 0.9[lambda]/[beta]cos[theta], (2)

where [lambda] is wave length of X-ray (0.15418 nm for Cu K[alpha]), [beta] is full width at half maximum (FWHM) in radian, [theta] is the diffraction angle, and D is particle diameter size [17]. The average particle size is 28.5 nm.

The 10 wt% Ag/SrSn[O.sub.3] composites were analyzed by XPS to identify the metallic state of silver ([Ag.sup.0]) on the surface of the composites, as shown in Figure 2. The XPS analysis reveals the existing peaks of strontium, carbon (tape), silver, tin, and oxygen, consistent with the chemical components of the Ag/SrSn[O.sub.3] composites. The binding energy of C1s line (285.1 eV) was used to calibrate all the binding energies. The analysis reveals the silver 3d spectral lines of spin-orbit doublet peaks with a splitting of 6.07 eV at the binding energy of 367.77 and 373.84 eV for [Ag3d.sub.5/2] and [Ag3d.sub.3/2], respectively. These binding energies correspond with those of the metallic silver of the previous reports 18-21], indicating the presence of [Ag.sup.0] in SrSn[O.sub.3] matrix. The Sn3d peaks of 10 wt% Ag/SrSn[O.sub.3] composites appear at 486.60 eV of [Sn3d.sub.5/2] and 494.98 eV of [Sn3d.sub.3/2], corresponding to [Sn.sup.4+] [22]. The Sr3d spectrum with spin-orbit doublet peaks corresponds to [Sr3d.sub.5/2] and [Sr3d.sub.3/2] peaks at 133.04 and 134.74 eV, respectively. They are in accordance with Sr2+ [23].

The as-synthesized pure SrSn[O.sub.3] and 1wt%, 5wt%, and 10wt% Ag/SrSn[O.sub.3] composites were analyzed by FTIR at room temperature over the range from 400 to 1000 [cm.sup.-1] (Figure 3). The vibration of the Sn[O.sub.3.sup.2-] stannate groups of pure SrSn[O.sub.3] was detected as high intensity band at 677 [cm.sup.-1] [24]. Moreover, the bands became shallower with increase in the amount of Ag contained in the Ag/SrSn[O.sub.3] composites, which indicates the interaction between silver and oxygen atoms in the stannate group of SrSn[O.sub.3]. The result proved that Ag nanoparticles were attached to the surface of SrSn[O.sub.3] samples.

The products were analyzed by electron microscopy (EM), energy dispersive X-ray (EDX) spectroscopy, and selected area electron diffraction (SAED), as shown in Figures 4, 5, 6, and 7. The SrSn[(OH).sub.6] precursors demonstrate the formation of rod-like product with the size distribution of about 300-745 nm in diameter and one to several microns in length. For pure SrSn[O.sub.3], it still retains the morphology as the SrSn[(OH).sub.6] precursors, but the rods became thinner with smooth surface due to the loss of hydroxyl group of the rod-like SrSn[(OH).sub.6] precursors by transforming into rod-like SrSn[O.sub.3]. The 10wt% Ag/SrSn[O.sub.3] composites remained at the same size and shape as pure SrSn[O.sub.3] with the aggregated

Ag nanoparticles (about 30 nm) formed on the surfaces of SrSn[O.sub.3] rods. The EDX qualitative analyses of 10wt% Ag/SrSn[O.sub.3] composites were recorded as the mapping images of Ag, Sr, Sn, and O, which show the distributive Ag nanoparticles over the SrSn[O.sub.3] matrix. The EDX spectrum also corresponds to the four prominent peaks belonging to the Sr-[L.sub.[alpha]], Sn-[L.sub.[alpha]], O-[K.sub.[alpha]1,2], and Ag-L[alpha] lines without any impurity detection. A SAED pattern shows diffraction rings of the polycrystalline rod-like SrSn[(OH).sub.6] precursors corresponding to the (301), (222), (512), and (441) crystallographic planes of the JCPDS database number 09-0086 [16]. SAED patterns of two single crystalline rods of pure SrSn[O.sub.3] and 10 wt% Ag/SrSn[O.sub.3] composites were indexed and specified as SrSn[O.sub.3] orthorhombic phase of the JCPDS database number 77-1798 [16] in accordance with the patterns obtained by simulation. It should be noted that Ag nanoparticles were not detected in the 10 wt% Ag/SrSn[O.sub.3] composites because the SAED interpretation was selected for characterization only on a very small area.

Figure 8 presents the UV-visible absorption spectra of pure SrSn[O.sub.3] and 1 wt%, 5 wt%, and 10 wt% Ag/SrSn[O.sub.3] composites. In this research, the absorption intensity increased significantly around 300 nm in short wavelength for pure SrSn[O.sub.3] rods, but it did not show the absorption in the visible region, corresponding to the previous reports [4, 24]. By doping with Ag, its absorption intensity on the short-wavelength side was steeply increased compared to that of pure SrSn[O.sub.3] rods. A small absorption band in the visible region at 437 nm started appearing in the absorption spectrum of the 1wt% Ag/SrSn[O.sub.3] composites and gradually shifted to the lower wavelength of 435 nm in the 10wt% Ag/SrSn[O.sub.3] composites. Detection of the absorption spectra in the visible light region for Ag/SrSn[O.sub.3] composites indicates an increase in the absorption intensity with an increase in the Ag content. It is well known that surface plasmon bands appearing in the visible region are characteristic of the noble metal nanoparticles with sizes ranging from 2 nm to 100 nm [25] and surface plasmons are collective oscillations of free electrons at metallic surface [26]. This absorption band is attributed to the characteristic surface plasmon resonance (SPR) phenomenon of free electron in the conduction bands of Ag nanoparticles. When Ag nanoparticles were irradiated by visible light, a large oscillating electric field originated around the metallic particles [26-30]. Clearly, this result indicates the presence of Ag nanoparticles contained in SrSn[O.sub.3] matrix synthesized by the ultrasonic vibration.

The degradation of MB dye in aqueous solution containing 5 wt% Ag/SrSn[O.sub.3] composites (Figure 9) under ultraviolet radiation was studied. The intensity decrease in the characteristic absorption peak of MB dye at 663 nm for different lengths of time clearly shows the efficiency of catalytic activity of the photocatalyst. For the decolorization efficiency of MB (Figure 10), almost no degradation of MB dye was detected in the catalyst-free solution although the exposure time was as long as 320 min. This result indicates that the contribution of self-degradation was negligible. But for the solutions containing pure SrSn[O.sub.3], 1wt% Ag/SrSn[O.sub.3], 5wt% Ag/SrSn[O.sub.3], and 10 wt% Ag/SrSn[O.sub.3] composites, the decolorization efficiencies within 320 min were 84.8, 86.3, 99.5, and 92.6%, respectively. These implied that 5wt% Ag/SrSn[O.sub.3] composites were the best photocatalyst for waste water treatment. The excess of Ag nanoparticles can cause deficiency in the photocatalytic activity of 10wt% Ag/SrSn[O.sub.3] composites by lowering the absorption of UV light, leading to the decrease in UV light utilization with negative effect to the photocatalytic process [31]. Moreover, the 5 wt% Ag/SrSn[O.sub.3] composites were recycled and reused five times to test the photocatalytic stability shown in Figure 11. The photocatalyst is still performing the decolorization efficiency at almost the same rate.

The photocatalysis for organic compounds decomposed by SrSn[O.sub.3] with and without Ag nanoparticles doping under ultraviolet radiation is proposed (Figure 12). For SrSn[O.sub.3], electrons in valence band (VB) were excited and transferred to conduction band (CB) under UV light radiation. Then, the photogenerated holes in VB combined with hydroxyl anions to form *OH oxidative species which would further decompose the organic compounds. The rapid recombination rate of electron-hole pairs can lead to low photocatalytic activity. When Ag nanoparticles were added to the SrSn[O.sub.3] product, the Ag nanoparticles acted as electron traps, inhibiting the electron-hole recombination process. Subsequently, the trapped electrons were transferred to the adsorbed [O.sub.2], which acted as electron acceptors. Thus *[O.sub.2.sup.-] oxidative species were generated and could effectively oxidize the MB dye. Holes still remained in the VB of SrSn[O.sub.3] and combined with [H.sub.2]O to form [H.sup.+] ions and *OH radicals. These oxidative species could effectively break down toxic organic substances back into original chemical forms of C[O.sub.2] and [H.sub.2]O creating a cleaner and safer environment [32]. The recombination of electron-hole pairs was inhibited, and the photochemical reaction for waste water treatment was enhanced [33, 34].

4. Conclusions

A solution containing strontium acetate and tin(II) chloride dihydrate with the pH of 12 was processed by a cyclic microwave radiation (CMR) to form SrSn[(OH).sub.6] precursors, which were calcined at 900[degrees]C for 3 h to form SrSn[O.sub.3]. Further, the SrSn[O.sub.3] precursors and AgN[O.sub.3] in ethylene glycol were ultrasonically vibrated to form Ag/SrSn[O.sub.3] composites, which were tested for photocatalysis under ultraviolet radiation for the degradation of MB dye as an organic model. In this research, the 5wt% Ag/SrSn[O.sub.3] composites showed the best photocatalyst due to the enhancement of electron-hole separation process.

http://dx.doi.org/10.1155/2014/261395

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors wish to thank the Thailand Research Fund (TRF) for providing financial support through the Royal Golden Jubilee Ph.D. Program and the TRF Research Grant BRG5380020 and the Thailand's Office of the Higher Education Commission through the National Research University (NRU) Project for Chiang Mai University (CMU), including the Graduate School of CMU through a general support.

References

[1] N. Zidi, S. Omeiri, B. Hadjarab, A. Bouguelia, A. Akroun, and M. Trari, "Transport properties and photo electrochemical characterization of oxygen-deficient ASn[O.sub.3-[delta]] (A=Ca, Sr and Ba)," Physica B, vol. 405, no. 16, pp. 3355-3359, 2010.

[2] M. C. F. Alves, S. Boursicot, S. Ollivier et al., "Synthesis of SrSn[O.sub.3] thin films by pulsed laser deposition: Influence of substrate and deposition temperature," Thin Solid Films, vol. 519, no. 2, pp. 614-618, 2010.

[3] C. Li, Y. Zhu, S. Fang et al., "Preparation and characterization of SrSn[O.sub.3] nanorods," Journal of Physics and Chemistry of Solids, vol. 72, no. 7, pp. 869-874, 2011.

[4] D. Chen and J. Ye, "SrSn[O.sub.3] nanostructures: synthesis, characterization, and photocatalytic properties," Chemistry of Materials, vol. 19, no. 18, pp. 4585-4591, 2007

[5] C. W. Lee, D. W Kim, I. S. Cho et al., "Simple synthesis and characterization of SrSn[O.sub.3] nanoparticles with enhanced photocatalytic activity," International Journal of Hydrogen Energy, vol. 37, no. 14, pp. 10557-10563, 2012.

[6] W. F. Zhang, J. Tang, and J. Ye, "Photoluminescence and photocatalytic properties of SrSn[O.sub.3] perovskite," Chemical Physics Letters, vol. 418, no. 1-3, pp. 174-178, 2006.

[7] H. Sinaim, A. Phuruangrat, S. Thongtem, and T Thongtem, "Synthesis and characterization of heteronanostructured Ag nanoparticles/Mo[O.sub.3] nanobelts composites," Materials Chemistry and Physics, vol. 132, no. 2-3, pp. 358-363, 2012.

[8] G. Li, K. Chao, C. Ye, and H. Peng, "One-step synthesis of Ag nanoparticles supported on AgV[O.sub.3] nanobelts," Materials Letters, vol. 62, no. 4-5, pp. 735-738, 2008.

[9] J. Ahmed, C. K. Blakely, S. R. Bruno, and V. V Poltavets, "Synthesis of MSn[O.sub.3] (M = Ba, Sr) nanoparticles by reverse micelle method and particle size distribution analysis by whole powder pattern modeling," Materials Research Bulletin, vol. 47, no. 9, pp. 2282-2287, 2012.

[10] M. C. F. Alves, M. R. Nascimento, S. J. G. Lima et al., "Influence of synthesis conditions on carbonate entrapment in perovskite SrSn[O.sub.3]," Materials Letters, vol. 63, no. 1, pp. 118-120, 2009.

[11] T Ding and J. Zhu, "Microwave heating synthesis of HgS and PbS nanocrystals in ethanol solvent," Materials Science and Engineering B: Solid-State Materials for Advanced Technology, vol. 100, no. 3, pp. 307-313, 2003.

[12] T Thongtem, A. Phuruangrat, and S. Thongtem, "Characterization of nano- and micro-crystalline CdS synthesized using cyclic microwave radiation," Journal of Physics and Chemistry of Solids, vol. 69, no. 5-6, pp. 1346-1349, 2008.

[13] E. Kwon, H. S. Lim, Y. K. Sun, and K. D. Suh, "Improved rate capability of lithium-ion batteries with Ag nanoparticles deposited onto silicon/carbon composite microspheres as an anode material," Solid State Ionics, vol. 237, pp. 28-33, 2013.

[14] Q. Liu, S. Sun, H. Li et al., "Preparation, characterization and photocatalytic activities of ZrWMo[O.sub.8]/Ag composites with core-shell structure," Applied Surface Science, vol. 261, pp. 593-597, 2012.

[15] G. Li, H. Liu, H. Zhao et al., "Chemical assembly of Ti[O.sub.2] and Ti[O.sub.2]@Ag nanoparticles on silk fiber to produce multifunctional fabrics," Journal of Colloid and Interface Science, vol. 358, no. 1, pp. 307-315, 2011.

[16] Powder Diffract File, JCPDS-ICDD, Delaware County, Pa, USA, 2001.

[17] T Theivasanthi and M. Alagar, "Electrolytic synthesis and characterization of silver nanopowder," Nano Biomedicine and Engineering, vol. 4, no. 2, pp. 58-65, 2012.

[18] B. Yu, K. M. Leung, Q. Guo, W M. Lau, and J. Yang, "Synthesis of Ag-Ti[O.sub.2] composite nano thin film for antimicrobial application," Nanotechnology, vol. 22, no. 11, Article ID 115603, 2011.

[19] S. Hu, F. Li, and Z. Fan, "A convenient method to prepare AG deposited N-Ti[O.sub.2] composite nanoparticles via N[H.sub.3] plasma treatment," Bulletin of the Korean Chemical Society, vol. 33, no. 7, pp. 2309-2314, 2012.

[20] W. Song, Y. Wang, H. Hu, and B. Zhao, "Fabrication of surface-enhanced Raman scattering-active ZnO/Ag composite microspheres," Journal of Raman Spectroscopy, vol. 38, no. 10, pp. 1320-1325, 2007

[21] X. Zhu, Z. Zhang, K. Wang et al., "A facile route to mechanically durable responsive surfaces with reversible wettability switching," New Journal of Chemistry, vol. 36, no. 5, pp. 1280-1284, 2012.

[22] M. Kwoka, L. Ottaviano, M. Passacantando, S. Santucci, G. Czempik, and J. Szuber, "XPS study of the surface chemistry of L-CVD Sn[O.sub.2] thin films after oxidation," Thin Solid Films, vol. 490, no. 1, pp. 36-42, 2005.

[23] V. Kozhukharov, M. Machkova, P. Ivanov, H. J. M. Bouwmeester, and R. van Doorn, "Surface analysis of doped lanthanide cobalt perovskites by X-ray photoelectron spectroscopy," Journal of Materials Science Letters, vol. 15, no. 19, pp. 1727-1729, 1996.

[24] P. Junploy, S. Thongtem, and T. Thongtem, "Photoabsorption and photocatalysis of SrSn[O.sub.3] produced by a cyclic microwave radiation," Superlattices and Microstructures, vol. 57, pp. 1-10, 2013.

[25] K. Mollazadeh-Moghaddam, B. V. Moradi, R. Dolatabadi-Bazaz, M. Shakibae, and A. R. Shahverdi, "An enhancing effect of gold nanoparticles on the lethal action of 2450 MHz electromagnetic radiation in microwave oven," Avicenna Journal of Medical Biotechnology, vol. 3, no. 4, pp. 195-200, 2011.

[26] S. S. Gasaymeh, S. Radiman, L. Y. Heng, E. Saion, and G. H. M. Saeed, "Synthesis and characterization of silver/polyvinilpirrolidone (Ag/PVP) nanoparticles using gamma irradiation techniques," African Physical Review, vol. 4, pp. 31-41, 2010.

[27] L. S. Daniel, H. Nagai, and M. Sato, "Absorption spectra and photocurrent densities of Ag nanoparticle/Ti[O.sub.2] composite thin films with various amounts of Ag," Journal of Materials Science, vol. 48, no. 20, pp. 7162-7170, 2013.

[28] X. Yin, W. Que, D. Fei, F. Shen, and Q. Guo, "Ag nanoparticle/ZnO nanorods nanocomposites derived by a seed-mediated method and their photocatalytic properties," Journal of Alloys and Compounds, vol. 524, pp. 13-21, 2012.

[29] R. Chahal, S. Mahendia, A. K. Tomar, and S. Kumar, "Effect of ultraviolet irradiation on the optical and structural characteristics of in-situ prepared PVP-Ag nanocomposites," Digest Journal of Nanomaterials and Biostructures, vol. 6, no. 1, pp. 301-308, 2011.

[30] Q. Wang, S. Wang, W. Hang, and Q. Gong, "Optical resonant absorption and third-order nonlinearity of (Au, Ag)-Ti[O.sub.2] granular composite films," Journal of Physics D: Applied Physics, vol. 38, no. 3, pp. 389-391, 2005.

[31] S. Hu, F. Li, and Z. Fan, "Preparation of Si[O.sub.2]-coated Ti[O.sub.2] composite materials with enhanced photocatalytic activity under UV light," Bulletin of the Korean Chemical Society, vol. 33, no. 6, pp. 1895-1899, 2012.

[32] C. Wu and J. Chern, "Kinetics of photocatalytic decomposition of methylene blue," Industrial and Engineering Chemistry Research, vol. 45, no. 19, pp. 6450-6457, 2006.

[33] C. Yu and J. C. Yu, "Sonochemical fabrication, characterization and photocatalytic properties of Ag/ZnW[O.sub.4] nanorod catalyst," Materials Science and Engineering B: Solid-State Materials for Advanced Technology, vol. 164, no. 1, pp. 16-22, 2009.

[34] C. Gu, C. Cheng, H. Huang, T Wong, N. Wang, and T Zhang, "Growth and photocatalytic activity of dendrite-like ZnO@Ag heterostructure nanocrystals," Crystal Growth & Design, vol. 9, no. 7, pp. 3278-3285, 2009.

Patcharanan Junploy, (1) Titipun Thongtem, (1) Somchai Thongtem, (2,3) and Anukorn Phuruangrat (4)

(1) Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200, Thailand

(2) Department of Physics and Materials Science, Faculty of Science, ChiangMai University, Chiang Mai 50200, Thailand

(3) Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200, Thailand

(4) Department of Materials Science and Technology, Faculty of Science, Prince of Songkla University, Hat Yai, Songkhla 90112, Thailand

Correspondence should be addressed to Titipun Thongtem; ttpthongtem@yahoo.com and Somchai Thongtem; schthongtem@yahoo.com

Received 22 January 2014; Revised 23 May 2014; Accepted 25 May 2014; Published 3 July 2014

Academic Editor: Tianxi Liu
COPYRIGHT 2014 Hindawi Limited
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2014 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Research Article
Author:Junploy, Patcharanan; Thongtem, Titipun; Thongtem, Somchai; Phuruangrat, Anukorn
Publication:Journal of Nanomaterials
Date:Jan 1, 2014
Words:4131
Previous Article:The long-term fate and toxicity of PEG-modified single-walled carbon nanotube isoliquiritigenin delivery vehicles in rats.
Next Article:Enhanced antifungal bioactivity of Coptis Rhizome prepared by ultrafining technology.
Topics:

Terms of use | Privacy policy | Copyright © 2020 Farlex, Inc. | Feedback | For webmasters