Chemical effect on wellbore instability of Nahr Umr shale.
The Nahr Umr Shale Formation is found throughout the southern part of the Arabian Gulf and forms the cap rock to many major reservoirs in the region . Major wellbore instability problems when drilling through this shale formation have often arisen not only in new wells but also in reentry wells, especially with the rise of water-based mud and stricter environmental control, making wellbore stability in this shale an extremely challenging operation for drilling/mud engineers.
The Halfaya Oilfield is in the south of Missan province in Iraq, which is 400 km south east of Baghdad, the capital of Iraq. Three horizontal wells in the Nahr Umr Formation of Halfaya Oilfield had been drilled. But, two wells of the three horizontal wells have sidetracking due to sticking, only one horizontal well is drilled successfully, so it illustrates the big effects of wellbore instability problems on the directional drilling in this oilfield.
2. Geological Character
The Halfaya Oilfield is located on the Arabian shelf, which is adjacent to the Zagros tectonic zone. The influence of Zagros tectonic movement is the extrusion to the Arabian shelf by the European plate (NNE-SSW). The propagation of the stress wave leads to a series of anticlines in the Arab shell. This extrusion stopped in Middle Miocene. The geological structure is a low dip anticline, in which the long axis is nearly perpendicular to the Zagros extrusion stress field [2-4]. The structure is above the Arabian shelf and is far away from the Zagros fault control zone, but the structure is still affected by Zagros tectonic movement, which makes the in situ stress complicated.
There is no large fault which could be recognized by seismic data. The anticline structure is also very smooth. The results show that the extrusion stress by the Zagros tectonic movement is not very strong, and the extrusion stress does not produce strong in situ deformation and destruction.
The lithologic characters in the Halfaya Oilfield from the top to the bottom is, respectively, the Tertiary Upper Fars Group, mainly sandy mudstone, about 1300 m thick; the Lower Fars Group, mainly anhydrite, salt rock, and shale deposit, about 500 m thick, being the regional cap rock; the Tertiary Kirkuk Group which is mainly sandstone and mudstone, about 300 m; from the Tertiary Jaddala group to the Nahr Umr group, mainly carbonatite and interlayers of thin marl, sandstone and shale.
3. Drilling Problems
Three horizontal wells, N001H, N006H, and N002H, in the Nahr Umr Formation of Halfaya Oilfield had been drilled. The well distributions are both located in the structural long axis direction. The complicated drilling problems of these three wells are as follows.
When the first horizontal well (N001ST well) encountered the Nahr Umr layer, there were two sidetracking operations. The first sidetracking happened at 3941.26 m, the SLB screw stuck in the highly deviated interval and the directional tool dropped in the well. The fishing failed, which led to sidetracking. The second sidetracking happened at 4091.21 m, the Nahr Umr Shale collapsed and this led to sticking at 4087 m the treatment measures was ineffective and a sidetracking operation happened.
The second horizontal well (N006ST well) used the organic salt drilling fluid which has a strong inhibition. When drilling 3964 m, the Nahr Umr Shale collapsed and the treatment measure for the sticking failed, so sidetracking happened at 3800 m using the vertical well completion.
The third horizontal well N002H used saturated salt water drilling, but there were many sticks between 3660 m and 3895 m in the Nahr Umr Formation, and there were cavings at the shaking screen.
The two wells of the three horizontal wells have sidetracking due to sticking, only one horizontal well was drilled successfully, so it illustrates the big effects of wellbore instability problems in the oilfield. The wellbore instability has serious impact for oilfield drilling, and it restricts the exploration and development in the oil field. As the development wells are generally directional wells or horizontal wells, and the wellbore instability risk is great, wellbore stability analysis is needed in the Halfaya Oilfield.
4. Wellbore Instability Mechanism
4.1. Character of the Instable Shale. Figure 1 shows the logging data of the Nahr Umr Formation of N004 well. The GR logging shows that the formations are mainly sandstone and shale. The caliper logging shows that there are both stable and instable intervals. Compared to the GR logging data, the lithology of collapsing interval is shale and the sandstone interval is stable. According to the interval transit time logging data, the interval transit time of the Nahr Umr Shale is obviously higher than the adjacent sandstone interval. The density logging data of the shale are obviously lower than the adjacent sandstone interval. The reasons for this phenomenon are the rich internal microfractures, drilling fluid, and the filtrate seepage. This can be seen from the photo of the Nahr Umr Shale (Figure 2). In addition, the shape of cavings of the Nahr Umr Shale indicates that the shale is enriched in fractures (Figure 3).
The main reason for wellbore instability in hard brittle shale with lots of fractures is as follows [5-11]. If the sealing capacity of the drilling fluid is not enough or the ionic concentration is not enough to balance the formation water ionic concentration, the drilling fluid and the filtrate would flow into the microfractures under the driving power from the fluid column pressure difference of drilling fluid and the ionic concentration difference. This would lead the friction coefficients of the fracture plane to decrease, the effective stresses around the wellbore to decrease, the formation around the wellbore to become loose, and the support of the drilling fluid column to the wellbore wall decrease. Thus the formation fluid will flow into the wellbore. During the reaming and back reaming, the disturbance of the rigs to the loose formation will lead to wellbore instability.
4.2. Wellbore Instability Analysis. In order to solve the wellbore instability of the fractured and hard-brittle shale in Nahr Umr Formation, the drilling fluid property and engineering countermeasures should be taken into account. We analyze the wellbore instability reasons combined with the drilling engineering measures of three horizontal wells in the Nahr Umr Formation.
When using rational engineering measures, the drilling fluid property decides the wellbore stability during drilling to a large extent. Table 1 shows the drilling fluid property used in these three horizontal wells. These three wells used three different types of drilling fluid. The following can be concluded from the drilling fluid property parameters in the table.
(1) Based on the mud rheological parameters, for the formation with good completeness, the rheological parameters of these three wells are similar and could meet the engineering requirement. But, for the fractured shale formation, the rheological parameters of these three wells are different. Compared to the other two wells, the drilling fluid of N001H well has a low viscosity, which is bad for carrying the cuttings and cavings. In addition, the drilling fluid with low viscosity will easily flow into the formation under the pressure difference. Therefore, the rheological parameters of drilling fluid of N002H well benefit wellbore stability. Usually increasing the drilling fluid viscosity is of benefit for fracture formation.
(2) Based on the drilling fluid filter loss, the filter losses of these three wells are similar. Because the filter loss is measured by the experimental instrument in the laboratory, the results cannot reflect the real formation situation and it is only a reference index.
(3) Based on the drilling fluid ionic concentration, although there are not ionic concentration parameters of N001H well drilling fluid in the daily drilling report, according to the drilling fluid description provided by the drilling fluid service provider, the drilling fluid ionic concentrations of this well could indicate that the ionic concentration of KCL Polymer drilling fluid used in the N001H well is between the concentrations of the N002H well and N006H well; the ionic concentration of the N002H well is the highest the ionic concentration of the N006H well is the lowest. When the hole is opened, the ionic concentration difference of the drilling fluid and formation water is the main driving force that drives the free water in the drilling fluid into the formation. Commonly, the high ionic concentration of drilling fluid is of benefit to prevent the free water in the drilling fluid from flowing into the formation. If the free water in the drilling fluid flows into the formation, the formation will be hydrated, and the formation strength will be decreased, so as to lead to wellbore periodic collapsing. Table 2 shows the formation water property of Halfaya Oilfield. The results show that the formation water has an extremely high ionic concentration, which needs a high ionic concentration for drilling fluid to balance it.
4.3. Shale Hydration. According to the formation character, the Nahr Umr Shale is abundant in microfractures; the formation is broken, and the drilling fluid can easily flow into the micro fracture plane, which leads to the change of formation strength. In order to prevent wellbore instability, the drilling fluid property should be improved. The influence of drilling fluid on the wellbore stability is analyzed from the mineral composition, the drilling fluid consistency, and the influence of the drilling fluid on formation strength.
Tables 3 and 4 illustrate the minerals and clay minerals composition and content of the Nahr Umr Shale, respectively. The test results in the tables show that the Nahr Umr Shale mainly consists of quartz and clay, especially quartz, which exceeds 48.5%. For shale Formation, the higher the quartz, the higher the brittleness; at the same time, the content of the clay minerals of the shale belongs to medium and little high level. The clay minerals mainly consist of illite/smectite and kaolinite, and the content of smectite is low. The type of the clay mineral indicates that the shale is very brittle. In addition, the kaolinite is a stable clay mineral, and the hydration of the illite/smectite is also feeble. The type and content of the clay minerals both indicate that Nahr Umr Shale Formation is a hard and brittle formation which is hard to hydrate.
According to research experience, if the drilling fluid inhibition is good enough, a formation like the Nahr Umr Shale is impossible to hydrate without expansion collapsing. Therefore, we evaluate the rejection capacity of three drilling fluid systems which are used in the Halfaya Oilfield. The three drilling fluids are organic salt drilling fluid, Gel-polymer drilling fluid, and KCl-polymer drilling fluid.
The densities of these three types of drilling fluid are all 1.33 g/[cm.sup.3]; then we measured the cuttings recovery (The 40 g cuttings with 3.2~2.0mm diameter injected to the 350 mL fluid. Roll 16 h in a set temperature. Then filter the cuttings through a sieve. Dry and weigh cuttings to calculate the cuttings recovery.) and swelling ratio of these three drilling fluids. The results are shown in Table 5. The results show that the cuttings recoveries of these three types of drilling fluid are both higher than 95% for the Nahr Umr Shale; although the swelling ratios are different. These results show that the inhibitive capacity of the drilling fluid is good ; on the other hand, the results indicate that the formation hydration is feeble. The inhibitive capacity of the drilling fluid is not the main reason for the wellbore instability of the Nahr Umr Shale.
In order to analyze the influence of the drilling fluid on the wellbore stability of the Nahr Umr Shale, experimental studies were carried on the influence of drilling fluid on the rock mechanical property. We tested the shale strength of Nahr Umr Shale after immersing it in different kinds of drilling fluids. Table 6 shows the uniaxial compressive strength (UCS, MPa) results from the test. Figure 4 illustrates the comparison of the strength variation rule versus the time after immersing in different kinds of drilling fluid.
Figure 4 shows that the shale UCS decreases greatly after immersing it in the organic salt drilling fluid, the next is the KCL-polymer drilling fluid; the strength in the Gel-polymer drilling fluid changed a little. Therefore, the Gel-polymer drilling fluid benefits the wellbore stability of the Nahr Umr Shale.
Under the drive force of the ionic concentration difference, the free water in the drilling fluid which flows into the formation would decrease the rock strength, which is the main reason for the collapse in Nahr Umr Shale; in addition, as the formation is extremely hard and brittle and the fractures are rich internally, if the drilling fluid sealing capacity is not good enough, the drilling fluid and filtrate would flow into the rock along the microfracture under the difference of the drilling fluid column pressure and pore pressure, so as to weaken the formation strength and lead to wellbore collapse. So, the increasing of the ionic concentration of the drilling fluid and enhancing the drilling fluid sealing capacity is the key to the wellbore stability of the Nahr Umr Shale.
5. Time-Dependent Collapse Pressure
According to mechanical concepts, the main reason for borehole collapse is caused by shear failure for the reason that stresses loaded on rock around the borehole exceed the rock strength, as a result of lower mud column pressure. Now, brittle formation collapse will generate and the borehole will enlarge; for plastic formation, plastic deformation be will generated and borehole shrinkage will be encountered.
Generally, borehole collapse takes place in the minimum horizontal stress direction, [theta] = [pi]/2 or 3[pi]/2 ; the borehole stress on minimum horizontal stress direction [13-20] is as follows:
[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII]. (1)
Assume that safe coefficient FS  is as follows:
FS = [[[sigma].sub.n]tg[phi] + C/[tau]]. (2)
M = 1 + (FS - 1) [cos.sup.2][phi]. (3)
Replace normal stress [[sigma].sub.n] as principal stress [[sigma].sub.1] and [[sigma].sub.3]:
[[sigma].sub.n] = [[[sigma].sub.1] + [[sigma].sub.3]/2] - [[[sigma].sub.1] - [[sigma].sub.3]/2] sin[phi] - [alpha][P.sub.p]. (4)
Rewrite Mohr-Coulomb criterion :
M([[sigma].sub.1] - [[sigma].sub.3]) - sin [phi] ([[sigma].sub.1] + [[sigma].sub.3] - 2[alpha][P.sub.p]) - 2C cos [phi] = 0. (5)
Based on different borehole stress conditions, borehole collapsing pressure expresses as a different form. When the bearing condition is [[sigma].sub.[theta]] > [[sigma].sub.z] > [[sigma].sub.r], maximum and minimum stress separately are [[sigma].sub.1] = [[sigma].sub.[theta]], [[sigma].sub.3] = [[sigma].sub.r], and make k = ([alpha](1 - 2v)/(1 - v)) -[psi]; under mud penetrating borehole face, the borehole collapsing pressure model is
[P.sub.cr] = (2C cos [phi] + (sin [phi] - M)(3[[sigma].sub.H] - [[sigma].sub.h]) + [[delta]Mk + sin [phi] (2[delta]f - [delta]k - 2k)][P.sub.p]) x [([delta]k sin [phi] - M (2 + [delta]k - 2[delta]f)).sup.-1]. (6)
For the hard-brittle shale of Nahr Umr Formation, according to the study results and experimental results, the influence of the drilling fluid immersion on the mechanical property mainly reflects in the decrease of the compressive strength as the immersing time increase.
Figure 5 illustrates the variation of collapse pressure versus the hole opening time for Nahr Umr Shale. The collapse pressure would increase as the formation strength decreases; the increasing speed decreases gradually. The increasing rate of Gel-polymer drilling fluid is the lowest; in a certain drilling fluid density it can keep the wellbore stability for the longest time. The increasing of the mud density could only keep the wellbore stability in limited time. If the
property of the drilling fluid cannot be improved, increasing the mud density would force the drilling fluid to flow into the formation and make the wellbore unstable.
6. Countermeasures Dealing with Wellbore Instability
In order to prevent the wellbore instability of Nahr Umr Shale, we come up with the following drilling technology countermeasures and suggestions.
(i) Depending only on the drilling fluid density cannot solve the wellbore stability of the shale formation which is full of fractures [22, 23]. If the drilling density is too high, the pore pressure would increase and the effective stresses around the wellbore decrease, and this would cause a larger damaged scale. Decreasing the drilling fluid filter loss and improving the drilling fluid rheological property would benefit wellbore stability.
(ii) Commonly, the larger the inclination, the more possible the wellbore instability. But for the laminar fracture formation, decreasing the angle of the wellbore axial line with the bedding normal direction is of benefit for the wellbore stability.
(iii) The influences of the swabbing pressure and surge pressure should be taken into consideration when evaluating wellbore stability; the simplified bottom hole assembly (BHA) could prevent large swabbing pressure and surge pressure and then prevent sticking.
(iv) The hydraulic jetting is not suitable, because the high pressure hydraulic jetting would produce water wedge effect in the progress of the drilling seepage. The big diameter jet or no-jet are welcomed.
(v) Avoiding the intense change of the dogleg or the well track so as to prevent big drill string acting force to the wellbore wall.
(vi) Optimizing the hydraulic parameters so as to ensure the cuttings could be carried out of the wellbore timely. For some situations, wellbore collapse can not be prevented, so carrying out the cuttings in a timely way could decrease the downhole complicated time. Increasing the drilling rate could decrease the exposed time of the shale formation, which is useful for the wellbore stability.
(vii) The formation water has an extremely high ionic concentration, so keep a high ionic concentration for the drilling fluid to balance it.
Under the function of the ionic concentration difference, the free water in the drilling fluid which flows into the formation will decrease the rock compressive strength, which is the main reason for the collapse in Nahr Umr Shale; in addition, as the formation is extremely hard and brittle and the fractures are internally rich, if the drilling fluid sealing capacity is not good enough, the drilling fluid and filtrate will flow into the rock along the micro fracture surface under the difference of the drilling fluid column pressure and pore pressure, so as to weaken the formation strength and lead to wellbore collapse. So, increasing the ionic concentration of the drilling fluid to enhance the drilling fluid sealing capacity is the key point to the wellbore stability of the Nahr Umr Shale Formation.
The collapse pressure will increase as the formation strength decreases after drilling; the increasing speed decreases gradually. The increasing rate of Gel-polymer drilling fluid is the lowest; in a certain drilling fluid density it can keep the wellbore stable for the longest time. The increase of the mud density could only keep the wellbore stability for a limited time. Improving the property of the drilling fluid is the basis for keeping the wellbore stable.
This work is financially supported by the Science Fund for Creative Research Groups of the National Natural Science Foundation of China (Grant no. 51221003) and National Oil and Gas Major Project of China (Grant no. 2011ZX05009005).
 V. X. Nguyen, Y. N. Abousleiman, and S. K. Hoang, "Analyses of wellbore instability in drilling through chemically active fractured-rock formations," SPE Journal, vol. 14, no. 2, pp. 283-301, 2009.
 Z. Nie, H. Liu, A. Liu et al., "The large temperature difference, long column and narrow clearance cementing best practices in Halfaya oilfield," in SPE Asia Pacific Oil and Gas Conference and Exhibition, October 2012.
 M. Zhang, Z. Tian, S. Xu et al., "Research and application of BH-ATH (anti-three high) drilling fluid system," in IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, July 2012.
 H. Rabia, Iraqi Oil Reserves: Opportunities for Production and Exploration, 2008.
 B. S. Aadnoy, "Introduction to special issue on borehole stability," Journal of Petroleum Science and Engineering, vol. 38, no. 3-4, pp. 79-82, 2003.
 B. S. Aadony, "Modeling of the stability of highly inclined boreholes in anisotropic rock formations," SPE Drilling Engineering, vol. 3, no. 3, pp. 259-268, 1987.
 F. J. Santarelli, C. Dardeau, and C. Zurdo, "Drilling through hinghly fractured formations: a problem, a medel, and a cure," in Proceedings of the SPE Annual Technical Conference and Exhibition, October 1992.
 O. A. Helstrup, Z. Chen, and S. S. Rahman, "Time-dependent wellbore instability and ballooning in naturally fractured formations," Journal of Petroleum Science and Engineering, vol. 43, no. 1-2, pp. 113-128, 2004.
 R. Narayanasamy, D. Barr, and A. Milne, "Wellbore instability predictions within the cretaceous mudstones, clair field, West of Shetlands," in Offshore Europe, Paper SPE 124464, Aberdeen, UK, 2009.
 B. H. Yu, Study on Borehole Unstable Mechanism of Layered Shale, China University of Petroleum, Beijing, China, 2006.
 J. L. Yuan, J. G. Deng, Q. Tan, B. H. Yu, and X. C. Jin, "Borehole stability analysis of horizontal drilling in shale gas reservoirs," Rock Mechanics and Rock Engineering, vol. 46, no. 5, pp. 1157-1164, 2013.
 J. N. Yan, Drilling Fluid Technology, China University of Petroleum Press, 2001.
 E. Fjaer, R. M. Holt, P Horsrud et al., Petroleum Related Rock Mechanics, Elsevier, 2nd edition, 2008.
 J. S. Bell and D. I. Gough, "Northeast-Southwest compressive stress in Alberta evidence from oil wells," Earth and Planetary Science Letters, vol. 45, no. 2, pp. 475-482, 1979.
 D. I. Gough and J. S. Bell, "Stress orientations from borehole wall fractures with examples from Colorado, East Texas, and Northern Canada," Canadian Journal of Earth Sciences, vol. 19, no. 7, pp. 1358-1370, 1982.
 M. D. Zoback, D. Moos, L. Mastin, and R. N. Anderson, "Well bore breakouts and in situ stress," Journal of Geophysical Research, vol. 90, no. 7, pp. 5523-5530, 1985.
 S. H. Hickman, J. H. Healy, and M. D. Zoback, "In situ stress, natural fracture distribution, and borehole elongation in the Auburn geothermal well, Auburn, New York," Journal of Geophysical Research, vol. 90, no. 7, pp. 5497-5512, 1985.
 C. A. Barton, M. D. Zoback, and K. L. Burns, "In-situ stress orientation and magnitude at the Fenton Geothermal site, New Mexico, determined from wellbore breakouts," Geophysical Research Letters, vol. 15, no. 5, pp. 467-470, 1988.
 B. C. Haimson and C. Chang, "True triaxial strength of the KTB amphibolite under borehole wall conditions and its use to estimate the maximum horizontal in situ stress," Journal of Geophysical Research, vol. 107, no. 10, pp. ETG 15-1-ETG 15-14, 2002.
 M. Chen, Y. Jin, and G. Q. Zhang, Petroleum Engineering Related Rock Mechanics, Science Press, Beijing, China, 2008.
 J. G. Deng, Y. F. Cheng, M. Chen, and B. H. Yu, Wellbore Stability Evaluation Technique, Petroleum Industry Press, 2008.
 V. Maury and C. Zurdo, "Drilling-induced lateral shifts along pre-existing fractures: a common cause of drilling problems," SPE Drilling & Completion, vol. 11, no. 1, pp. 17-24, 1996.
 X. Chen and C. P Tan, "The impact of mud infiltration on wellbore stability in fractured rock masses," in SPE/ISRM Rock Mechanics Conference, 78241, October 2002.
Baohua Yu, (1) Chuanliang Yan, (1) and Zhen Nie (2)
(1) State Key Laboratory of Petroleum Resource and Prospecting, China University of Petroleum, Beijing 102249, China
(2) Exploration & Production Research Institute, CNPC, Beijing 100011, China
Correspondence should be addressed to Chuanliang Yan; firstname.lastname@example.org
Received 15 July 2013; Accepted 8 September 2013
Academic Editors: A. M. Efstathiou and A. Vorontsov
TABLE 1: The drilling fluid properties of three horizontal wells of Nahr Umr Formation. Well no. N001H N001H N002H well N006H well-Hole 1 well-Hole 2 well Mud type KCL-polymer KCL-polymer Salt BH-WEI saturated Density 1.25 1.25 1.28 1.28 (g/[cm.sup.3]) Viscosity (s) 51 53 78 65 Plastic 26 27 41 39 viscosity (cp) Y.P (lb/100 24 26 31 29 [ft.sup.2]) Gel strength 5/8 5/14 7/9 5/7 10"/10' (lb/100 [ft.sup.2]) API filtrate (mL) 3.2 3.4 3.0 3 Mud cake (mm) 0.3 0.3 0.3 0.5 PH 9.5 9 9 8.5 Solid (%) 13 11 13 17 Sand (%) 0.3 0.3 0.2 0.3 Bentonite 27 26 38 content (g/L) Potassium (mg/L) 27000 Chloride (mg/L) 55000 11520 [Ca.sup.+] (mg/L) 200 TABLE 2: The formation fluid properties of Halfaya oilfield. Unit Nahr Umr Water type Ca[Cl.sub.2] PH 6.3 Specific gravity sg 1.121 (15.56[degrees]C) Resistivity ohm*m 0.068 (25[degrees] C) Total salinity ppm 166661 Total hardness mg/L 16562 [Na.sup.+] mg/L 60015 [Ca.sup.2+] mg/L 8681 [Mg.sup.2+] mg/L 993 [Fe.sup.2+] mg/L 74 [Ba.sup.2+] mg/L 1 [K.sup.+] mg/L 716 [Sr.sup.2+] mg/L 356 [Cl.sup.-] mg/L 107098 S[O.sub.4.sup.2-] mg/L 874 HC[O.sub.3.sup.-] mg/L 7263 C[O.sub.3.sup.2-] mg/L 0 O[H.sup.-] mg/L 0 TABLE 3: Mineral composition and content of the Nahr Umr Shale. Depth Mineral content (%) Quartz Potassium Soda Anorthose Anorthose feldspar feldspar 3645.10 51.7 0.8 0.2 3649.83 60.8 1.2 0.4 3666.00 48.5 1.9 0.3 1.4 Depth Mineral content (%) Dolomite Iron Hematite TCCM pyrite 3645.10 2.7 44.6 3649.83 4.7 32.9 3666.00 4.5 43.4 TABLE 4: Clay mineral composition and content of the Nahr Umr Shale. Clay mineral content (%) Interbed ratio (% S) Depth S I/S It Kao C C/S I/S C/S 3645.10 34 7 48 11 14 3649.83 33 3 40 24 11 3666.00 44 7 49 21 TABLE 5: Swelling ratio and recovery of the Nahr Umr Shale. Organic salt KCL-polymer Gel-polymer Recovery Rate (%) 95 96 97 Swelling Ratio (%) 24 36 22 TABLE 6: Experimental results of shale UCS after immersing in drilling fluid. Drilling fluid type Organic salt KCL-polymer Gel-polymer UCS without immersing 48.62 51.09 47.22 (MPa) UCS with immersing of 40.16 44.8 44.8 24 h (MPa) UCS with immersing of 37.81 41.41 43.02 48 h (MPa) UCS with immersing of 35.64 39.82 41.69 72 h (MPa) UCS with immersing of 34.96 39 40.33 96 h (MPa)
|Printer friendly Cite/link Email Feedback|
|Title Annotation:||Research Article|
|Author:||Yu, Baohua; Yan, Chuanliang; Nie, Zhen|
|Publication:||The Scientific World Journal|
|Date:||Jan 1, 2013|
|Previous Article:||A novel method for the accurate evaluation of Poisson's ratio of soft polymer materials.|
|Next Article:||Echocardiographic assessment of cardiac structural and functional indices in broiler chickens treated with silver nanoparticles.|