Printer Friendly

Any dolt can dig a hole, but ... it takes a genius to do it right.

So, big shot, you think you know how to dig postholes, eh? Sure you do--anyone can dig a hole. But how hard do you want to work, and how often do the holes end up in the wrong spot and you have to start over? Here are a few tips to get perfectly placed holes--with a little less sweat on your part.


The big 4 posthole tools

If you have more than a couple of postholes to dig, don't stop at a shovel and a clamshell digger. You'll treasure two more tools just as much. Pick up a tile spade. The long, narrow blade will get you places no other shovel can. Also get a tamper-end digging bar.


Dig by hand unless ...

Power augers require a trip to the rental store and a brawny friend. And they're worthless in clay or rocky soil. The truth is, unless you have lots of holes to dig in sand, it's often easier to dig by hand.

Use water and the back of your shovel

If you're digging in sticky clay soil, dip your clamshell digger in a bucket of water so the soil won't stick. Knock off clumps on the back of the shovel. Spread a tarp to keep dirt off your grass.

Small is beautiful

Unless you're a body builder, avoid those giant, heavy-gauge, fiberglass-handled clamshell diggers. You'll just get exhausted; you're better off with a smaller, lightweight digger.

1 String your line and pound the I stakes

String a line marking the outside edges of the posts. Mark the post centers on the line by untwisting the string and pushing a nail through the strands. You can fine-tune the nail position just by sliding it to the exact location. Then pound stakes to mark the center of the holes, if you're using 4x4 posts, that will be just under 2 in. from the string.

2 Carve out a soil divot with a spade

Set the string aside so you don't wreck it while digging. And don't just start digging away; drill yourself a pilot hole first. Carve out a round plug to outline the posthole. That'll get you started in exactly the right spot. Throw the dirt onto a tarp to protect your lawn.

3 Loosen earth with a tile shovel

Unless you have very soft soil, you'll work way too hard digging with just a clamshell digger. Loosen the soil and carve away at the sides with the tile spade. It'll easily slice through small roots.

4 Use your clamshell digger

Plunge the open clamshell digger blades into the loosened soil and grab a load of fill.

5 Use a recip saw on large roots

Don't kill yourself chiseling out roots. Just use a recip saw with a long, coarse blade and poke it right into the soil at the ends of the root and cut it off.

6 Dislodge rocks with a digging bar

Pick out rocks from the hole sides with your digging bar. Let them fall into the hole and pluck them out with your clamshell digger.

7 Tamp soil with the other end

Use the tamper end of the digging bar to compact the soil before setting posts or pouring concrete. That prevents any settling.

8 Mark the post edge locations

Restring the line, pull the nails and mark the exact post edge locations on the line with a permanent marker.

9 Cover holes with plywood

If you're walking away from the postholes for a while, cover them with plywood. It just might save a broken leg and/or keep the sides from caving in during a storm.

10 Set the posts

Place the posts with one side brushing against the string and the edge even with your mark. Then hold the post plumb while you fill the hole. Pack the soil with the tamper end of the digging bar every foot

by Travis Larson
COPYRIGHT 2011 Home Service Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2011 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Author:Larson, Travis
Publication:The Family Handyman
Geographic Code:1USA
Date:Jul 1, 2011
Previous Article:Garden shed: bright and spacious, easy to access--our best garden shed yet.
Next Article:Give hopeless grass a fresh start.

Terms of use | Privacy policy | Copyright © 2019 Farlex, Inc. | Feedback | For webmasters