Printer Friendly

A low cost RF transceiver for 2.4 GHz DSSS short-range communication systems.

In this article, the design and experimental results of a low cost RF transceiver for short-range wireless systems are described. The transceiver is composed of a direct Gaussian frequency shift keying (GFSK) modulation transmitter and a dual conversion low IF architecture receiver. In the transmitter, the filtered data is applied directly to the tuning port of the voltage-controlled oscillator (VCO). The frequency output of the VCO is converted to the 2.4 GHz band with an optimized frequency tripler. The output power of the transmitter is 22 dBm and the spur rejection is better than 40 dBc. A low cost LNA is optimized for the receiver and the tested receiving sensitivity is -100 dBm.

**********

The development of short-range wireless systems has captured the industry's imagination for several decades. (1) Many of these systems operate at the internationally available unlicensed industrial, scientific and medical (ISM) 2.4 GHz frequency band. The attraction of these systems is that they can offer low cost, small physical size (single chip) and low power consumption. Some systems, like Bluetooth, utilize frequency hopping spread spectrum (FHSS) technology, where the system will frequency hop 1,600 times a second, delivering short time division multiplexed packets with each hop. With spread spectrum hopping, the sequence is random and the receiver must hunt down the chosen transmission frequency after each hop. Some systems, like the IEEE 802.11 Wireless Local Area Networks (WLAN), utilize direct sequence spread spectrum (DSSS) technology, which spreads the signal over several frequencies, and can switch channels to avoid interference.

A low cost, miniature-size, high performance RF transceiver is an important component in these systems. Many short-range RF transmitters utilize direct FSK modulation to simplify the RF circuitry. In these systems, the VCO is directly modulated with the transmit data. To improve the isolation between the RF power amplifier and the VCO, the VCO usually operates at a lower frequency, and a frequency-multiplier is used to convert the VCO frequency to the transmitting frequency. Because the frequency-multiplier produces many unwanted spurs, its performances, such as efficiency and spur rejection, are of great importance. For further spur rejection, additional RF bandpass filters are generally needed. Therefore, the frequency-multiplier and RF filter should be carefully designed and optimized to satisfy the specifications. The RF receivers utilize a dual conversion architecture for high sensitivity and selectivity. The functional diagram of the RF transceiver investigated in this article is shown in Figure 1.

[FIGURE 1 OMITTED]

[FIGURE 2 OMITTED]

FREQUENCY TRIPLER

The schematic of the frequency tripler is shown in Figure 2. Generally, there are two basic sections of the frequency-multiplier: the harmonic generation section and a filter section. (2,3) The high frequency transistor Q1 serves as the harmonic generator. C1 and L1 form the input-matching network. L2, C3 and C5 serve as the output-matching network and the filter section. R1, R2, R3, C2, C4, C6, L1 and L2 form the bias network.

The performance of the frequency tripler is mainly determined by the input and output matching networks. The function of the input-matching network is to ensure that the RF transistor is excited adequately enough to generate harmonic components. The output-matching network usually resonates at the required harmonic frequency to reject unwanted harmonics. To achieve high performance, the tripler should be optimized. The harmonic balance method is a suitable and powerful approach for simulation and optimization. The simulated results of the frequency tripler, output waveform and spectrum are shown in Figure 3.

The third harmonic is generated and the fundamental frequency and other harmonics are rejected. The frequency tripler is excited with an 800 MHz CW signal at the level of 0 dBm. The output level at 2.4 GHz is -3 dBm, and the level of unwanted harmonics is less than -9 dBm. To satisfy the emission specification, additional filters are employed. Microstrip interdigital filters, which have the properties of small size, low insertion loss and good out-of-band rejection, are suitable for the transmitter.

[FIGURE 3 OMITTED]

[FIGURE 4 OMITTED]

LNA DESIGN

The schematic of the LNA is shown in Figure 4. The LNA is composed of a low cost RF BJT, bias circuits and matching networks. Its performance is optimized for noise figure, gain, and input and output return losses.

The simulation and optimization of the LNA is carried out with Agilent ADS. The simulated noise figure is less than 1.4 dB, the power gain is about 10 dB, and the input and output return losses are better than -12 dB in the frequency range from 2.4 to 2.5 GHz (see Figure 5).

[FIGURE 5 OMITTED]

EXPERIMENTAL RESULTS

A 2.4 GHz short-range RF transceiver was developed using the frequency tripler and the described LNA. It is a DSSS transceiver with GFSK modulation in the frequency range of 2.4 GHz. The data rate is 1.5 Mbps. The output spectrum of the transmitter is shown in Figure 6.

[FIGURE 6 OMITTED]

In the transmitter, besides the frequency tripler, a very simple microstrip interdigital filter with only three strips is used between the frequency tripler and the power amplifier. Taking advantage of the good performance of the frequency tripler, high spur rejection is achieved. The output power of the transmitter is 22 dBm, and the rejection of the fundamental and unwanted harmonics is better than 40 dBc.

The measured noise figure of the LNA is 1.8 dB, which is very close to the simulated result. The measured BER performance of the receiver was found to be less than 0.01 at an input RF power of -100 dBm.

CONCLUSION

A 2.4 GHz short-range RF transceiver with an RF frequency tripler and a low cost LNA is investigated. The frequency tripler, the key component of the transmitter, is optimized for both conversion gain and spur rejection. The LNA is optimized for best sensitivity. The test results show that the transceiver shows good performance and is very suitable for short-range radio applications.

References

1. F.L. Dacus, "Design of Short-range Radio Systems," Microwaves & RF, September 2001, pp. 73-80.

2. C. Murray, "Frequency Tripler," Student Reports, Johns Hopkins University EE787 MMIC Design Course, Fall 1997.

3. V. Uzunoglu, "Oscillator Network Performs a Diverse Range of Functions," Microwaves & RF, August 1996, pp. 115-128.

JIANYI ZHOU, JIANING ZHAO, WEI HONG AND XIAOWEI ZHU

Southeast University

Nanjing, China
COPYRIGHT 2004 Horizon House Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2004 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Technical Feature; Radio Frequency; direct sequence spread spectrum
Author:Zhou, Jianyi; Zhao, Jianing; Hong, Wei; Zhu, Xiaowei
Publication:Microwave Journal
Geographic Code:1USA
Date:Jun 1, 2004
Words:1052
Previous Article:Characteristics of a wide-band, high gain, eight-element slot antenna for PCS, IMT-2000 and WLL-band.
Next Article:An E-/D-mode pHEMT process for high performance switch and amplifier components utilizing multi-level high density interconnects.
Topics:

Terms of use | Privacy policy | Copyright © 2018 Farlex, Inc. | Feedback | For webmasters