Printer Friendly

A dual-mode bandpass filter with multiple controllable transmission-zeros using T-shaped stub-loaded resonators.

1. Introduction

There has been tremendous growth in unlicensed national information infrastructure (U-NII) radio band applications, including radio frequency identification (RFID) and WiMax applications [1-3]. Planar BPFs, with their compact size, low insertion loss, stringent frequency selectivity, and wide stopband, are in high demand among these applications. Generally, dual-mode resonators can be widely used to meet this demand because of their advantageous compact size. Wolff [4] first demonstrated dual-mode resonators in 1972. Later, dual-mode microstrip resonators became attractive because each can be used as two independent resonant circuits, allowing a compact topology size. Several other types of dual-mode resonators have been proposed, including circular ring [5], open stub [6], circular disk [7], and triangular patch [8] resonators. However, these resonators have only one TZ near the passband.

Selectivity is another critical issue for BPFs and can be improved by introducing TZs near the passband. Usually, nonadjacent coupling, including cross coupling and S-L coupling, can generate TZs by providing a multipath effect [9]. A wide stopband can be obtained by these out-of-band TZs. The cascade trisection and cascade quadruplet are two of the most commonly used cross coupling topologies, but both lead to a large circuit size. S-L couplings have also been widely used in microstrip BPFs. In [10,11], circular and rectangular dual-mode filters with S-L coupling were proposed. Those filters introduce two TZs at the stopband utilizing the S-L coupling.

In this study, we present the design for a dual-mode BPF for RFID or WiMax applications. The characteristics of the proposed TSSLRs are analyzed by dual-mode theory. Two capacitive and inductive S-L couplings are introduced to generate more TZs without increasing the implementation area. The proposed BPF shows a high out-of-band rejection level and second harmonic suppression.

2. C-Band BPF Design

The layout of the microstrip planar BPF is shown in Figure 1(a), which is composed of a dual-mode TSSLR, as shown in Figure 1(b). The characteristics of the TSSLR can be explained using the odd-even-mode theory. The full-wave electromagnetic (EM) Sonnet simulator was used to simulate the response of the dual-mode TSSLR, and the simulation results are illustrated in Figure 2. As seen, the even-mode resonant frequency varies with the parameter [L.sub.8]. We change [L.sub.8] from 5.6 mm to 7.1 mm, the even-mode is shifted from a lower to a higher frequency, while the odd-mode is not changed. Furthermore, Figures 3(a) and 3(b) show the current distribution of the two modes, respectively. There is a voltage null along the middle of the TSSLR under the odd-mode operation. In this case, the loaded element has no effect on the odd-mode characteristic, which is the reason why the parameter [L.sub.8] cannot shift the odd-mode. Under the even-mode operation, a virtual open circuit occurs along the axis of symmetry, so almost all of the current is concentrated on the proposed stub. Hence, the characteristic impedance of the proposed TSSLRs can accurately control both the odd- and even-mode resonant frequencies.

Figure 4 shows the proposed capacitive and inductive SL couplings and coupling topology, where the empty disks represent the source and load, respectively. The solid disks represent the odd-mode and even-mode. The input signal is coupled to two modes using coupled-line coupling [12] (represented by the solid lines), as is the output signal. The dashed lines represent the S-L couplings. The coupling topology is analyzed by means of the coupling matrix M, given by [13,14]


An explicit mathematical expression with respect to the coupling elements and the TZs is provided by

[OMEGA] = ([M.sub.11][M.sup.2.sub.S2] - [M.sub.22][M.sup.2.sub.S1])/([M.sup.2.sub.S2] - [M.sup.2.sub.S1]) (2)

where [absolute value of [M.sub.S1]] > [absolute value of [M.sub.S2]] is always true for this structure because the coupling strength between the odd-mode and the external feed-line is always larger than that of the even-mode. Therefore, this structure will at least have one TZ at finite frequency. Moreover, the resonant frequencies of the odd-mode and even-mode are related to [M.sub.S1] and [M.sub.S2], which can be expressed as

[f.sub.odd] = [f.sub.0] (1 - [M.sub.11] x [DELTA]f/2[f.sub.0]), (3)

[f.sub.even] = [f.sub.0] (1 - [M.sub.22] x [DELTA]f/2[f.sub.0]), (4)

where [f.sub.0] and [DELTA]f are the center frequency and the bandwidth, respectively. Using (1) and 3), a new expression of [OMEGA] can be obtained as


If [M.sub.11] > 0 and [M.sub.22] < 0, [OMEGA] would be greater than zero and [f.sub.even] > [f.sub.0] > [f.sub.odd]. The inherent TZ is at the upper stopband. In contrast, if [M.sub.11] < 0 and [M.sub.22] > 0, H would be greater than zero and [f.sub.even] < [f.sub.0] < [f.sub.odd]. The inherent TZ is at the lower stopband. Thus, the inherent TZ is always on the same side of the passband with the even-mode resonant frequency [15], as shown in Figure 2.

With regard to the proposed TSSLRs, the location of the inherent TZ relates to the even-mode, which can be changed by the value of [L.sub.8]. The TZ shifts from the lower stopband to the upper stopband when [L.sub.8] increases from 5.6 mm to 7.1 mm, as shown in Figure 2. In this study, the inherent TZ is located at the upper stopband due to [f.sub.even] > [f.sub.0] > [f.sub.odd], which leads to a very good selectivity.

Except for the inherent TZ, four additional TZs are created by introducing two S-L couplings at both the lower and upper stopbands, which results in a wide stopband and a high second harmonic suppression. At the same time, the location of these four TZs can be adjusted by the amount of capacitance or inductance of the S-L coupling, as demonstrated in Figure 5.

As shown in Figure 5, the gap [g.sup.1] determines the capacitance of the S-L coupling, whereas the coupling lengths [L.sub.5] and [L.sub.6] determine the inductance of the S-L coupling. Figure 5(b) shows the simulated results of the proposed BPF with varied values of [g.sup.1]. When the value of [g.sup.1] decreases, the additional [T.sub.Z4] moves to the passband. Similarly, Figures 5(a) and 5(c) show the simulated responses of the proposed BPF with varied values of [L.sub.5] and [L.sub.6], respectively. When the values of [L.sub.5] and [L.sub.6] change, the [TZ.sub.2] and [TZ.sub.3] are shifted very little, while the other TZs are moved. Consequently, the inherent TZ and the four additional TZs can be controlled to achieve a good selectivity and high level of rejection at the stopband due to the modification of the amount of nonadjacent coupling capacitance and inductance.

3. Results and Discussion

Based on the proposed TSSLRs, a dual-mode BPF is fabricated using a Teflon substrate with a relative dielectric constant of 2.54, a thickness of 0.54 mm, and a loss tangent of 0.002. Following the preceding design process, the dimensions are determined as follows: [L.sub.1] = 3.75 mm, [L.sub.2] = 1.95 mm, [L.sub.3] = 3 mm, [L.sub.4] = 6.4 mm, [L.sub.5] = 8.6 mm, [L.sub.6] = 3.8 mm, [W.sub.1] = 1.5 mm, [W.sub.2] = 1 mm, [W.sub.3] = 1 mm, [W.sub.4] = 0.9 mm, [g.sup.1] = 0.4 mm, and [g.sub.2] = 0.2 mm, with an overall size of 7.9 x 11.1[mm.sup.2], as shown in Figure 6.

The fabricated BPF was tested and characterized using an Agilent 8510C vector network analyzer (VNA). The narrowband simulation and measurement results of the proposed BPF are demonstrated in Figure 7. As seen from the measurement results, the resonant frequency is exactly at 5.73 GHz, with an insertion loss of 1.75 dB, a return loss of 28.18 dB, and a FBW of 8.4%. Five controllable TZs are located at 4.08 GHz, 4.38 GHz, 6.02 GHz, 9.5 GHz, and 13.27 GHz, with attenuation level of more than 30 dB. The last two attenuation poles can be shifted near the second harmonic frequency, which gives this BPF a wide stopband and high rejection level.

4. Conclusion

In this study, a miniaturized narrow-band BPF using proposed TSSLRs is designed, simulated, and fabricated. The performance of the TSSLRs was studied using the odd-even-mode method and verified by a full-wave EM simulator. The proposed TSSLRs have an inherent TZ, and two modified feed-lines are used to generate more TZs at the stopband for high level rejection and harmonic suppression. The measured responses show that this BPF exhibits five TZs due to the introduced capacitive and inductive S-L couplings. The proposed BPF has potential to be applied in C-band RFID and WiMax applications.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper. 10.1155/2014/572360


This work was supported by the National Research Foundation of Korea (NRF) Grant funded by the Korea government (MEST) (no. 2012R1A1A2004366). This work was also supported by a Research Grant of Kwangwoon University in 2013.


[1] R. K. Maharjan and N. Y. Kim, "Compact stub-coupled square open-loop bandpass filter for ku-band applications," Journal of Electromagnetic Waves and Applications, vol. 26, no. 5-6, pp. 603-614, 2012.

[2] R. K. Maharjan, B. Shrestha, and N. Y. Kim, "Compact microstrip square open-loop bandpass filter using open stubs" Electronics Letters, vol. 48, no. 6, pp. 333-334, 2012.

[3] Y. Li, C. Wang, and N. Y. Kim, "Compact and high-selectivity dual-band bandpass filter with tunable passband for wimax and wlan applications" Microwave and Optical Technology Letters, vol. 55, no. 9, pp. 2106-2110, 2013.

[4] I. Wolff, "Microstrip bandpass filter using degenerate modes of a microstrip ring resonator" Electronics Letters, vol. 8, no. 12, pp. 302-303, 1972.

[5] M. Matsuo, H. Yabuki, and M. Makimoto, "Dual-mode stepped-impedance ring resonator for bandpass filter applications" IEEE Transactions on Microwave Theory and Techniques, vol. 49, no. 7, pp. 1235-1240, 2001.

[6] X. H. Wu, Q. X. Chu, and F. C. Chen, "Dual-band bandpass filter with controllable bandwidth and good selectivity by using stub-loaded resonators," Microwave and Optical Technology Letters, vol. 54, no. 6, pp. 1525-1528, 2012.

[7] X. C. Zhang, Z. A. Yu, and J. Xu, "Design of microstrip dual-mode filters based on source-load coupling," IEEE Microwave and Wireless Components Letters, vol. 18, no. 10, pp. 677-679, 2008.

[8] L. P. Zhao, X. W. Dai, Z. X. Chen, and C. H. Liang, "Novel design of dual-mode dual-band bandpass filter with triangular resonators" Progress in Electromagnetics Research, vol. 77, pp. 417-424, 2007.

[9] M. Q. Zhou, X. H. Tang, and F. Xiao, "Miniature microstrip bandpass filter using resonator-embedded dual-mode resonator based on source-load coupling," IEEE Microwave and Wireless Components Letters, vol. 20, no. 3, pp. 139-141, 2010.

[10] C. K. Liao and C. Y. Chang, "Modified parallel-coupled filter with two independently controllable upper stopband transmission zeros," IEEE Microwave and Wireless Components Letters, vol. 15, no. 12, pp. 841-843, 2005.

[11] C. L. Wei, B. F. Jia, Z. J. Zhu, and M. C. Tang, "Hexagonal dual-mode filter with four transmission zeros," Electronics Letters, vol. 47, no. 3, pp. 195-196, 2011.

[12] J. S. Hong and M. J. Lancaster, Microstrip Filters for RF/Microwave Applications, John Wiley & Sons, New York, NY, USA, 2001.

[13] C. L. Wei, B. F. Jia, Z. J. Zhu, and M. C. Tang, "Design of different selectivity dual-mode filters with E-shaped resonator," Progress in Electromagnetics Research, vol. 116, pp. 517-532, 2011.

[14] C. K. Liao, P. L. Chi, and C. Y. Chang, "Microstrip realization of generalized Chebyshev filters with box-like coupling schemes," IEEE Transactions on Microwave Theory and Techniques, vol. 55, no. 1, pp. 147-153, 2007.

[15] J. S. Hong, H. Shaman, and Y. H. Chun, "Dual-mode microstrip open-loop resonators and filters," IEEE Transactions on Microwave Theory and Techniques, vol. 55, no. 8, pp. 1764-1770, 2007.

Zh. Yao, C. Wang, and N. Y. Kim

RFIC Center, Kwangwoon University, 447-1 Wolgye-dong, Nowon-ku, Seoul 139-701, Republic of Korea

Correspondence should be addressed to N. Y. Kim;

Received 8 October 2013; Accepted 31 December 2013; Published 9 February 2014

Academic Editors: H.-W. Wu and J.-K. Xiao
COPYRIGHT 2014 Hindawi Limited
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2014 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Research Article
Author:Yao, Zh.; Wang, C.; Kim, N.Y.
Publication:The Scientific World Journal
Article Type:Report
Date:Jan 1, 2014
Previous Article:Electronically tunable quadrature oscillator using grounded components with current and voltage outputs.
Next Article:Numerical simulation on slabs dislocation of Zipingpu concrete faced rockfill dam during the Wenchuan earthquake based on a generalized plasticity...

Terms of use | Privacy policy | Copyright © 2021 Farlex, Inc. | Feedback | For webmasters |