Printer Friendly

10 tips for better ripping: making long, straight rips in boards or plywood looks easy, but it takes skill and practice to do it safely and accurately. We've assembled a few of the most useful tips from experienced carpenters and cabinetmakers to help make ripping simpler and safer.

1 Use an 8d nail as a third hand

If you're without a table saw and need to rip boards with a circular saw, here's a tip to make the job a lot easier. Drive an 8d nail through the board and into the sawhorse to prevent the board from slipping while you rip it. When you're done ripping, just pull the board off the sawhorse, flip it over and pound the nail through and pull it out. It only takes a few seconds and eliminates the frustration of a slipping board.

2 Build a custom push block

Here's a push block that works great and keeps your hand safely away from the blade. It's just a piece of 1/2-in, plywood with notches to fit 1/4-in., 1/2-in., 3/4-in. and 1-1/2-in, boards or plywood. The notches help hold the board tight to the saw table, and the top handle slides along the top of your fence.

Make the notched plywood 11/16 in. taller than the height of your fence. Then glue it to a 3/4-in.-thick board with a handle attached.

3 Check the fence alignment

It's critical that the fence be parallel to the saw blade. If it's not, the blade will bind on the wood and cause a burned edge on your board, or worse, a dangerous kickback. If you have a saw with a top-quality fence that locks down squarely, then you should only need to check and adjust the fence the first time you use it. Read your owner's manual for instructions on adjusting your fence. Fences on less expensive saws can be inconsistent, and you'll need to check every time you reposition the fence.

Here's how: Measure the distance between a saw tooth and the fence at the front and back of the blade. Raise the blade fully for the most accurate check. For an accurate reading, make sure to choose two teeth that lean toward the fence. If the measurements are different, either adjust the fence or nudge it into position until the measurements are equal before locking it down.

4 Make narrow rips safely

The problem with making repetitive narrow rips on a table saw is that the blade guard and the fence are too close together to allow a push stick to fit between them. The solution is to move the fence away from the blade and clamp the sled base to the fence. Then build a push sled like the one shown to push the narrow rip through the blade. The sled slides under the blade guard and keeps your hand a safe distance from the blade, allowing you to make thin rips safely and easily.

To use this setup, rip your board as you normally would by sliding it against the fence extension. When you get within reach of your push sled, hook the sled behind the board you're ripping and push it through, just like you would if you were using a regular push stick.

5 Straighten a crooked edge

If you run the crooked edge of a board against the table saw fence, you'll still have a crooked board when you're done. Or worse, the board will get bound between the fence and the blade during the cut.

Here's a handy, low-tech way to straighten the edge of any board. Just fasten the crooked-edge board to a straight strip of plywood, letting it overhang the edge. Then run the straight edge of the plywood against your table saw fence to make a perfectly straight edge on your crooked board.

6 Mount a featherboard for accurate rips

There are times when you want your rips to be super accurate, like when you're building face frames, door parts or other cabinet components. The key to accurate rips is to keep the edge of the board in constant, tight contact with the fence. It's easy with a featherboard mounted on your table saw top. This Kreg True-FLEX featherboard ($20 at home centers and online) has expanding rails that lock into the miter gauge track.

If you have a cast iron bed on your table saw, you could buy a featherboard that attaches with super-strong magnets that make it simple to position and adjust. You can also make your own featherboard out of wood, and clamp it to the saw. Some saw manuals have instructions for this, or you can search online. Adjust the featherboard to apply a small amount of pressure to the board as you feed it through the blade. Make sure the "feathers" are in front of the infeed side of the saw blade to prevent binding. With a featherboard, your rips will be dead-on accurate every time.

7 Make table saw-quality rips with a circular saw

Even if you own a table saw, sometimes it's easier to rip large sheets of plywood with a circular saw. The trick to a perfectly straight cut is to clamp a straightedge to the plywood and use it as a guide for your saw. On most circular saws, the distance between the edge of the saw's base and the blade is 1-1/2 in., so you can simply position the straightedge 1-1/2 in. from your cutting line. But measure this distance on your saw to be sure.

You can buy a straightedge or use the factory edge of a plywood sheet. If your straightedge only has one straight edge, be sure to mark it to avoid using the crooked side.

8 Support long boards

Table saws excel at ripping long boards, but it's dangerous to do it without supporting the board as it leaves the saw.

There are all kinds of ways to provide support. We're using a Ridgid Flip Top work support. The top surface swivels to allow the board to ride onto the support without catching. You can buy a support like this for about $30 at Home Depot.

There are several other types of outfeed supports you can buy, or just build your own. What's important is that you use a support every time you make Long rips on a table saw.

9 To rip large sheets, you need well-trained help

Sometimes you need assistance to rip large sheets. The trouble is, most helpers try to be too helpful. They naturally want to grab the plywood and pull it or push it or steer it. Before you start, take time to teach your helper the right way. Instruct your helper to simply support the plywood, flat palms up, level with the saw bed, and let you do all the work. The helper should move along with the wood, but never grab the board or try to direct it. These simple rules will keep you both safe, and allow you to make a straight rip with no danger of binding or kickback.

10 Use a half fence for unruly boards

Wood with knots or wavy grain and wood that has been dried unevenly will often warp badly as you rip it. If the halves bend outward, one will push against the fence and could cause burn marks or a dangerous kickback. If this begins to happen, shut off the saw and remove the board. You can rip the board safely by clamping a smooth, straight length of 3/4-in, wood against the fence, ending at the center of the saw blade. This half fence gives the trapped piece (the section between the blade and the fence) room to bend without pushing back against the blade. Keep push sticks handy so you can work around the clamps and complete the cut smoothly.

BY JEFF GORTON editors@thefamilyhandyman.com
COPYRIGHT 2013 Home Service Publications, Inc.
No portion of this article can be reproduced without the express written permission from the copyright holder.
Copyright 2013 Gale, Cengage Learning. All rights reserved.

Article Details
Printer friendly Cite/link Email Feedback
Title Annotation:Top Ten TIPS
Author:Gorton, Jeff
Publication:The Family Handyman
Date:Feb 1, 2013
Words:1274
Previous Article:Outsmart woodpeckers.
Next Article:12 trailer upgrades.
Topics:

Terms of use | Privacy policy | Copyright © 2021 Farlex, Inc. | Feedback | For webmasters |