This Important Book Will Be A Standard Reference For All Those Conducting Thermal Cycling Oxidation Testing Or Assessing Its Implications In Such Sectors As The Power Industry.DUBLIN, Ireland -- Research and Markets (http://www.researchandmarkets.com/reports/c66024) has announced the addition of "Standardisation Noun 1. standardisation - the condition in which a standard has been successfully established; "standardization of nuts and bolts had saved industry millions of dollars" standardization Of Thermal Cycling Exposure Testing" to their offering. Standardisation of thermal cycling exposure testing: EFC EFC Expected Family Contribution EFC Expect(ed) Further Clearance EFC Evangelical Fellowship of Canada EFC Evangelical Free Church EFC Eastfield College EFC Everton Football Club EFC Electronic Fee Collection 53 - Provides the essential background for an appropriate code of practice - Reviews the range of existing test procedures The thermal cyclic cyclic /cyc·lic/ (sik´lik) pertaining to or occurring in a cycle or cycles; applied to chemical compounds containing a ring of atoms in the nucleus. cy·clic or cy·cli·cal adj. 1. oxidation oxidation /ox·i·da·tion/ (ok?si-da´shun) the act of oxidizing or state of being oxidized.ox·idative ox·i·da·tion n. 1. The combination of a substance with oxygen. 2. test has become one of the most widely accepted ways of measuring high temperature corrosion High temperature corrosion is also known as "hot corrosion". Hot corrosion by sulfates Two types of sulfate-induced hot corrosion are generally distinguished : Type I takes place above the melting point of sodium sulfate and Type II occurs below the melting point of . There has long been a need for an agreed code of practice with standardised Adj. 1. standardised - brought into conformity with a standard; "standardized education" standardized standard - conforming to or constituting a standard of measurement or value; or of the usual or regularized or accepted kind; "windows of standard width"; methods and procedures to ensure both the comparability and reliability of the results obtained. Based on an EU project, 'Cyclic oxidation testing - development of a code of practice for the characterisation of high temperature materials performance' (COTEST), this volume provides the essential background to an appropriate code of practice. The first part of the book reviews the range of existing test procedures. Part 2 summarises research on the influence of various test parameters on thermal cycling oxidation behaviour, including both long dwell and short dwell thermal cycling oxidation. The third and final part of the book describes the resulting code of practice which is being considered by the ISO/TC 156 Working Group 13 responsible for an appropriate international standard. With its distinguished editor and team of contributors, this important book will be a standard reference for all those conducting thermal cycling oxidation testing or assessing its implications in such sectors as the power industry. Contents: PART 1 METHODS AND PROCEDURES IN THERMAL CYCLING OXIDATION TESTING PRIOR TO COTEST Survey of existing test procedures and experimental facilities S Osgerby, National Physical Laboratory, UK Introduction. Summary of layout. Temperature control. Heating/cooling practice. Atmosphere. Testpieces - geometry, Preparation and handling. Measurement/evaluation techniques. Conclusions. Compilation of cyclic oxidation data R Pettersson, SIMR SIMR Swedish Institute for Metals Research SIMR Sutter Institute for Medical Research SIMR Systems Interchange Modification Report SIMR System Integration Management Review SIMR Signal to Inter-Modulation Ratio , Sweden Introduction. Cycle length and test duration. Materials and environments. Variability of results. Influence of experimental variables. Conclusions. Statistical analysis of cyclic oxidation data S Coleman, D. McGeeney, Newcastle University, UK and R Pettersson, SIMR, Sweden Test parameters. Comparing and summarising the mass change data. Statistical analysis - within sources. Statistical analysis - across data sources. Number of replicates required for future experiments. Conclusions. Recommendations. Sources of further information and advice. References. PART 2 EXPERIMENTAL INVESTIGATIONS ON THE INFLUENCE OF TEST PARAMETER VARIATION ON THERMAL CYCLING OXIDATION BEHAVIOUR Standardised test procedures, definitions and statistical design of experiments for investigation of test parameter variation on thermal cycling oxidation testing M Schutze, M Malessa, DECHEMA e.V., Germany and S Coleman, Newcastle University, UK Introduction. Preparation of corrosion test specimen and equipment. Different thermal cycles investigated. Analysis of results and post-test evaluation. Statistical design of experiments. The effect of heating on the total oxidation time G Strehl, G Borchardt, Technische Universitat Clausthal, Germany Introduction. Heating of the sample. Oxide Growth under nonisothermal conditions. Influence of the heating phase on the oxidation time. Conclusion. Acknowledgments. References. Investigation of the influence of parameter variation in long dwell thermal cycling oxidation L Niewolak, W J Quadakkers, Forschungzentrum Julich, Germany Introduction. Experimental setup. Experimental results. Investigation of the influence of parameter variation in short dwell thermal cycling oxidation M Schutze, M Malessa, DECHEMA e.V., Germany Introduction. Experimental investigation of reference materials under internally standardized standardized pertaining to data that have been submitted to standardization procedures. standardized morbidity rate see morbidity rate. standardized mortality rate see mortality rate. thermal cycling oxidation conditions. Investigation of the influence of parameter variation in ultra short dwell thermal cycling oxidation J R Nicholls, Cranfield University Cranfield University is a British postgraduate university based on three campuses. The main campus is at Cranfield, Bedfordshire, England. The others are at Shrivenham, Oxfordshire, and Silsoe, also in Bedfordshire, some , UK Introduction. Definition of suitable test conditions. Possible alternative test procedures. Design of a 'Focused light' rapid thermal cycle test facility. Design of a joule heating Joule heating is the process by which the passage of an electric current through a conductor releases heat. It was first studied by James Prescott Joule in 1841. Joule immersed a length of wire in a fixed mass of water and measured the temperature rise due to a known current device for wire and foil materials. Ultra short dwell' experiments. Conclusions. Burner A drive that writes write-once optical discs such as CD-Rs and DVD-Rs. A "burner" implies a one-time recording, but the term is erroneously used to refer to drives that "write" to re-recordable CD-RW and DVD-RW/+RW media as well. See burn, CD-R and DVD-R. rig thermal cycling oxidation testing A Kliewe, MTU Aero Engines MTU Aero Engines is Germany's leading aircraft engine manufacturer, develops, manufactures and provides service support for aircraft engines, military and civil alike. MTU Aero Engines was formerly known as MTU München. GmbH, Germany and S Osgerby NPL 1. NPL - New Programming Language. IBM's original (temporary) name for PL/I, changed due to conflict with England's "National Physical Laboratory." MPL and MPPL were considered before settling on PL/I. Sammet 1969, p.542. 2. Ltd., UK Introduction. Low velocity burner rig. High velocity burner rig. Thermal cycling oxidation testing in sulphidising atmospheres C Rinaldi, L Torri, CESI CESI Centro Elettrotecnico Sperimentale Italiano (Italy) CESI Chauffe-Eau Solaire Individuel CESI Centre d'Etudes Superieures Industrielles (French) CESI Canadian Educational Standards Institute S.p. A., Italy and H P Bossmann, Alstom Power Ltd., Switzerland Introduction. Fe-based materials. Ni-based materials. Thermal cycling oxidation testing under deposits Introduction. Definition of suitable test conditions. Deposit testing (WP5B). PART 3 CODE OF PRACTICE Validation testing of the code of practice and statistical analysis of experimental results Final Code of Practice Final Remarks For more information visit http://www.researchandmarkets.com/reports/c66024 |
|
||||||||||||
Printer friendly
Cite/link
Email
Feedback
Reader Opinion