Rebuilding in-house capabilities.

Rebuilding in-house capabilities

The following grid lists the in-house rebuilding capabilities of
rebuilt machinery dealers in four major areas of rubber processing
machinery. The capabilities listed for each dealer are based on
their responses to a mail questionnaire. Several dealers indicated
that they did not have these capabilities but could arrange for
these services and were not included in the grid.

                                        Akron Special    Akron Steel
                                          Machinery      Fabricators

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters
Build mill bases                              *               *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating                           *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls                               *

                                            Alsop
                                          Industrial
                                           Services     ASB Industries

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings                *
Build motor starters                          *
Build mill bases                              *
Rebuild gear reducers                         *
Install microprocessor controls               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                                         *
Build complete control panels                 *
Rework the gland ring                         *               *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber
Rebuild gears                                 *
Heavy equipment handling capability           *
Verify integrity of rebuilt parts             *
Rebuild rotors and grind to spec.             *
Welding capability-hardness coating
Rebuild to original specs.                    *
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin          *
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls               *

                                           Barwell        E.H. Benz

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls                               *

Presses

Remachine main cylinder
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram
Rework bolster guides
Build complete control panels
Rework the gland ring
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals          *
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls               *

                                             BRJ          Commission
                                         Engineering       Brokers

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls

Presses

Remachine main cylinder
Furnish hydraulic units
Install microprocessor controls               *
Rebuild the ram
Rework bolster guides
Build complete control panels                 *
Rework the gland ring                         *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls

                                            Davey
                                          Industries    Davis-Standard

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                *
Make low speed chain couplings
Build motor starters                          *
Build mill bases                              *
Rebuild gear reducers
Install microprocessor controls               *

Presses

Remachine main cylinder                       *
Furnish hydraulic units                       *
Install microprocessor controls               *
Rebuild the ram                               *
Rework bolster guides                         *
Build complete control panels                 *
Rework the gland ring                         *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls               *               *

                                            Ensine           Epco

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.                                    *
Install/design microprocessor control

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin          *
  barrel technology
Rebuild transmission bearings, seals          *               *
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls               *               *

                                          Erie Mill
                                           & Press        Erie Press

Mills/Calenders

Regrind rolls                                 *
Cut connecting gears                          *
Replace bronze sleeve bearings                *
Make low speed chain couplings                *
Build motor starters                          *
Build mill bases                              *
Rebuild gear reducers                         *
Install microprocessor controls               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                         *               *
Build complete control panels                 *               *
Rework the gland ring                         *               *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber
Rebuild gears                                 *
Heavy equipment handling capability           *
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating           *
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals          *
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls               *

                                                          Gomaplast
                                            Farrel        Machinery

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                *               *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                              *
Rebuild gear reducers                         *               *
Install microprocessor controls               *               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber                      *
Rebuild gears                                 *
Heavy equipment handling capability           *               *
Verify integrity of rebuilt parts             *               *
Rebuild rotors and grind to spec.             *
Welding capability-hardness coating           *
Rebuild to original specs.                    *
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin          *
  barrel technology
Rebuild transmission bearings, seals          *               *
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and                 *               *
  technology
Install microprocessor controls               *               *

                                           Hancock          Hudson
                                         Engineering      Machinery

Mills/Calenders

Regrind rolls                                 *
Cut connecting gears
Replace bronze sleeve bearings                *
Make low speed chain couplings
Build motor starters
Build mill bases                              *
Rebuild gear reducers                         *
Install microprocessor controls               *

Presses

Remachine main cylinder
Furnish hydraulic units                                       *
Install microprocessor controls
Rebuild the ram                                               *
Rework bolster guides
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber                      *
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts             *
Rebuild rotors and grind to spec.             *
Welding capability-hardness coating           *
Rebuild to original specs.                    *
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals          *
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls

                                            Hunter           Icon
                                          Hydraulics      Industries

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                            Jarvis
                                          Industries     JM Machinery

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears                                          *
Replace bronze sleeve bearings                                *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                                       *
Install microprocessor controls               *               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                 *               *
Rework the gland ring                                         *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating                           *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls                               *

                                           Johnson
                                          Machinery     Karder Rubber

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears                                          *
Replace bronze sleeve bearings                                *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                       *               *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                           Klockner        Kobelco
                                           Stewart         Stewart
                                           Boiling         Boiling

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters
Build mill bases                                              *
Rebuild gear reducers
Install microprocessor controls                               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                         *               *
Build complete control panels                 *               *
Rework the gland ring                         *               *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating                           *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls

                                        Mackey Bowley       M.I.R.

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *
Install microprocessor controls               *
Rebuild the ram                               *               *
Rework bolster guides                         *
Build complete control panels                 *
Rework the gland ring                         *               *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating                           *
Rebuild to original specs.                                    *
Install/design microprocessor control

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                          New Castle      NFM Iddon
                                         Ind. (Xaloy)      Limited

Mills/Calenders

Regrind rolls                                 *
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters                                          *
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder
Furnish hydraulic units
Install microprocessor controls
Rebuild the ram
Rework bolster guides
Build complete control panels
Rework the gland ring
Install microprocessor control panels

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews                  *               *
Install new or replace pin barrel             *               *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals          *               *
  and gears
Apply hardness coating to screw and/or        *               *
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls                               *

                                         NFM Welding      Northeast
                                          Engineers       Millwright

Mills/Calenders

Regrind rolls                                 *               *
Cut connecting gears                          *               *
Replace bronze sleeve bearings                *               *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                              *               *
Rebuild gear reducers                         *               *
Install microprocessor controls               *               *

Presses

Remachine main cylinder                       *
Furnish hydraulic units                       *
Install microprocessor controls               *
Rebuild the ram                               *
Rework bolster guides                         *
Build complete control panels                 *
Rework the gland ring                         *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability           *               *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.             *               *
Welding capability-hardness coating           *               *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                  *               *
Install new or replace pin barrel             *               *
  mixing pins
Redesign screw to fit customer needs          *               *
Convert drive and gear torque to pin          *               *
  barrel technology
Rebuild transmission bearings, seals          *               *
  and gears
Apply hardness coating to screw and/or        *               *
  feed section
Rebuild to latest designs and                 *               *
  technology
Install microprocessor controls               *               *

                                          OEM Press
                                           Systems      Old Mill Sales

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers                                         *
Install microprocessor controls               *

Presses

Remachine main cylinder                       *
Furnish hydraulic units                       *
Install microprocessor controls               *
Rebuild the ram                               *
Rework bolster guides                         *
Build complete control panels                 *
Rework the gland ring                         *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber
Rebuild gears                                                 *
Heavy equipment handling capability           *
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                                           Reliable
                                                           Rubber &
                                         RAK Machine       Plastic

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears                          *               *
Replace bronze sleeve bearings                *               *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                              *               *
Rebuild gear reducers                         *               *
Install microprocessor controls                               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                         *               *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                 *               *
Heavy equipment handling capability           *               *
Verify integrity of rebuilt parts             *               *
Rebuild rotors and grind to spec.             *               *
Welding capability-hardness coating           *               *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                  *               *
Install new or replace pin barrel             *               *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals          *               *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls                               *

                                            Rogers
                                          Industrial     Rubber City
                                           Products       Machinery

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears                                          *
Replace bronze sleeve bearings                                *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                         *               *
Build complete control panels                 *               *
Rework the gland ring                         *               *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                                  *
Install new or replace pin barrel                             *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls                               *

                                                          Scantland
                                            Rutil         Industries

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                         *               *
Build complete control panels                 *               *
Rework the gland ring                         *               *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin                          *
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or                        *
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls               *               *

                                                             SME
                                        Skinner Engine  Equipment LLC

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                                *
Make low speed chain couplings
Build motor starters
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls

Presses

Remachine main cylinder
Furnish hydraulic units
Install microprocessor controls
Rebuild the ram
Rework bolster guides
Build complete control panels
Rework the gland ring
Install microprocessor control panels

Internal Mixers

Remachine mixing chamber                      *               *
Rebuild gears                                 *               *
Heavy equipment handling capability           *               *
Verify integrity of rebuilt parts             *               *
Rebuild rotors and grind to spec.             *               *
Welding capability-hardness coating           *               *
Rebuild to original specs.                    *               *
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews
Install new or replace pin barrel             *               *
  mixing pins
Redesign screw to fit customer needs                          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or        *               *
  feed section
Rebuild to latest designs and                                 *
  technology
Install microprocessor controls

                                         Soberay and      Technical
                                          Sons Ltd.     Machine Prod.

Mills/Calenders

Regrind rolls                                 *               *
Cut connecting gears                          *               *
Replace bronze sleeve bearings                *               *
Make low speed chain couplings                *               *
Build motor starters
Build mill bases                              *               *
Rebuild gear reducers                         *               *
Install microprocessor controls               *               *

Presses

Remachine main cylinder                       *               *
Furnish hydraulic units                       *               *
Install microprocessor controls               *               *
Rebuild the ram                               *               *
Rework bolster guides                         *               *
Build complete control panels                 *               *
Rework the gland ring                         *               *
Install microprocessor control panels         *               *

Internal Mixers

Remachine mixing chamber                      *               *
Rebuild gears                                 *               *
Heavy equipment handling capability           *               *
Verify integrity of rebuilt parts             *               *
Rebuild rotors and grind to spec.             *               *
Welding capability-hardness coating           *               *
Rebuild to original specs.                    *               *
Install/design microprocessor control         *               *

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin          *
  barrel technology
Rebuild transmission bearings, seals          *
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls               *

                                                         U.S. Molding
                                         ThyssenKrupp     Machinery

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings                *
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls

Presses

Remachine main cylinder                       *
Furnish hydraulic units                       *               *
Install microprocessor controls               *
Rebuild the ram                               *
Rework bolster guides                         *               *
Build complete control panels                 *
Rework the gland ring                         *
Install microprocessor control panels         *

Internal Mixers

Remachine mixing chamber                      *
Rebuild gears                                 *
Heavy equipment handling capability           *
Verify integrity of rebuilt parts             *
Rebuild rotors and grind to spec.             *
Welding capability-hardness coating           *
Rebuild to original specs.                    *
Install/design microprocessor control         *

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals
  and gears
Apply hardness coating to screw and/or        *
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                                            Videx
                                         Vander Kemp      Equipment

Mills/Calenders

Regrind rolls
Cut connecting gears
Replace bronze sleeve bearings
Make low speed chain couplings
Build motor starters
Build mill bases
Rebuild gear reducers
Install microprocessor controls

Presses

Remachine main cylinder
Furnish hydraulic units                       *
Install microprocessor controls
Rebuild the ram
Rework bolster guides                         *
Build complete control panels
Rework the gland ring
Install microprocessor control panels

Internal Mixers

Remachine mixing chamber
Rebuild gears
Heavy equipment handling capability           *
Verify integrity of rebuilt parts
Rebuild rotors and grind to spec.
Welding capability-hardness coating
Rebuild to original specs.
Install/design microprocessor control

Extruders

Recut and profile feedscrews
Install new or replace pin barrel
  mixing pins
Redesign screw to fit customer needs
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or
  feed section
Rebuild to latest designs and
  technology
Install microprocessor controls

                                        Wayne Machine     West Coast
                                            & Die           Rubber

Mills/Calenders

Regrind rolls                                                 *
Cut connecting gears                                          *
Replace bronze sleeve bearings                                *
Make low speed chain couplings                                *
Build motor starters                                          *
Build mill bases                                              *
Rebuild gear reducers                                         *
Install microprocessor controls                               *

Presses

Remachine main cylinder                                       *
Furnish hydraulic units                                       *
Install microprocessor controls                               *
Rebuild the ram                                               *
Rework bolster guides                                         *
Build complete control panels                                 *
Rework the gland ring                                         *
Install microprocessor control panels                         *

Internal Mixers

Remachine mixing chamber                                      *
Rebuild gears                                                 *
Heavy equipment handling capability                           *
Verify integrity of rebuilt parts                             *
Rebuild rotors and grind to spec.                             *
Welding capability-hardness coating                           *
Rebuild to original specs.                                    *
Install/design microprocessor control                         *

Extruders

Recut and profile feedscrews                  *
Install new or replace pin barrel             *
  mixing pins
Redesign screw to fit customer needs          *
Convert drive and gear torque to pin
  barrel technology
Rebuild transmission bearings, seals                          *
  and gears
Apply hardness coating to screw and/or        *               *
  feed section
Rebuild to latest designs and                 *
  technology
Install microprocessor controls                               *